Hobby Heaven Zephyr Nozzle Wrench (HHA-7101) – Airbrush Nozzle Removal Tool
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Maintenance
- Accessory
- Zephyr
DWG · Product Information
PROJ: HHA-7101 · SHEET 2 / 4
View · Overview
Product overview
HHA-7101 is the small flat spanner packed in every Hobby Heaven Zephyr box, here on its own. On the Zephyr the nozzle sits threaded in the front end of the body and is too tiny to turn by hand, so this wrench is what removes it for a deep clean or a swap and what refits it afterwards. One wrench handles both Zephyr nozzle sizes, 0.3 mm (HHA-2101) and 0.5 mm (HHA-2102). Most buyers want it because the original has disappeared, or to keep a second one in their cleaning kit.
- Identical to the wrench supplied with the Zephyr
- Open-ended head that takes either nozzle size
- Thin, flat blank that reaches into the nose of the airbrush
- Hole at the handle end for a hook or key ring
- One tool per Hobby Heaven blister, marked HHA-7101 with barcode
Removing and refitting the nozzle
Disconnect the air and flush the airbrush. Take off the needle cap and nozzle cap, then pull the needle back so its point is clear. Seat the wrench head fully, hold it level with the body and unscrew; once the nozzle frees, finish by hand. To refit, run the nozzle in with your fingers until it stops and give the wrench just a small extra turn, because too much force splits nozzles. Check first that its rubber O-ring is on the nozzle rather than left inside the body. On the Zephyr the needle comes out and goes back through the nose with the nozzle removed, so a needle change begins with this tool as well.
Wrench, or something else?
| What you see | Likely reason and next step |
|---|---|
| Nozzle refuses to turn | Paint dried in its thread: soak the nose in airbrush cleaner and try again gently; pliers crush nozzles |
| Wrench keeps slipping off | Not pushed fully home, or held at an angle |
| Head spread or bent | Replace the wrench before it chews the nozzle |
| Cup bubbling, or a leak at the nose once refitted | Nozzle loose or O-ring missing: look for the O-ring, then a fraction more turn |
| Spray spits or pulls sideways once refitted | Perhaps a split nozzle tip: fit a new nozzle (HHA-2101 or HHA-2102) |
Signs it needs replacing
A spread, twisted or burred head, or a wrench that has gone astray. A worn wrench costs less than the nozzle it can damage.
Worth knowing
Store it with the airbrush, not in a general toolbox, so it is to hand whenever the nozzle has to come out. It is made for the Zephyr; it may well suit nozzles on other airbrushes, but none has been tried by us, so treat any other fit as untested. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
- Nozzle wrench
- Cleaning brushes
- Cleaning needles
- Nozzle reamer
Product
Hobby Heaven Zephyr Nozzle Wrench (HHA-7101) – Airbrush Nozzle Removal Tool
Code (proj)
HHA-7101
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet