HHA-5202 is a 3 m braided air hose, long enough for the compressor to live on the floor, beneath the bench or next to a spray booth rather than at your elbow, which also takes its noise further from your ear and leaves room to turn a model or stand up. The two ends carry matching knurled nuts threaded 1/8" BSP female, so direction does not matter and both tighten by hand. It suits the Hobby Heaven Zephyr, as our photo shows, and any other airbrush or compressor with 1/8" BSP male connections. If the compressor sits right beside you, the shorter HHA-5201 (1.8 m) leaves less hose lying on the desk.
3 m long, roughly 10 ft
Matching 1/8" BSP female nuts, knurled for grip
Black braid over its whole length
Pictured on the Zephyr with our valved quick disconnect, HHA-5104, sold separately
Comes in a Hobby Heaven bag marked HHA-5202 with its barcode
Which hose for your setup?
Your setup
What to use
Compressor on the desk or a shelf just behind
1.8 m (HHA-5201) is enough
Compressor on the floor, beneath the bench or by a booth
This 3 m hose
Zephyr, Iwata, Harder & Steenbeck, Sparmax, Grex or Master airbrush
1/8" BSP inlet: connects directly
Badger, Paasche or Aztek airbrush
Fit that brand's inlet adapter first
Compressor outlet 1/8" BSP male
Connects directly
Compressor outlet 1/4" BSP male
Add a 1/4" female to 1/8" male reducer (in HHA-5401)
US compressor with 1/4" NPT
An NPT-to-BSP adapter: the two threads do not seal together
When the air misbehaves
Hoses seldom fail. A hiss at an end is nearly always the joint: refit the nut squarely and, if it persists, tape the male thread. A nut that stops after one turn has met a different thread, so reach for an adapter rather than force. Water spitting from the nozzle is condensation from the compressor; an inline trap such as HHA-5301 catches it at the airbrush. Air leaking through the braid means a split, usually from crushing or kinking, and then the hose should go, as it should when a nut cracks or its thread strips.
Fitting and care
Switch off at the compressor and bleed the line. Tighten one end on the outlet and the far end on the airbrush or a quick-disconnect coupler, by hand. Restore the air and dab soapy water on each connection to spot bubbles. Set your pressure while spraying, because any hose reads a touch lower with air flowing. Coil it loosely and keep solvents, soldering irons and knives clear of it.
Worth knowing
One long hose avoids joining two short ones, and so removes a joint that could leak. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
03
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?+
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?+
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?+
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?+
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?+
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
04
Notes · Logistics
Shipping
Orders placed before 3pm (Mon–Fri) are dispatched the same day. UK delivery is by Royal Mail 24 Tracked. Free UK delivery on orders over £70. International delivery available via Royal Mail International Tracked or courier.
Returns
If you're not happy with your purchase, contact us within 30 days for a full refund or exchange. Items must be unused and in original packaging.