HHA-3302 Zephyr airbrush control knob shown enlarged beside its Hobby Heaven blister, 1 knob with O-ring supplied

Hobby Heaven Zephyr Rear Control Knob (HHA-3302) – Preset Paint Flow Limiter with O-Ring

£3.29
Sale price  £3.29 Regular price 
Skip to product information
HHA-3302 Zephyr airbrush control knob shown enlarged beside its Hobby Heaven blister, 1 knob with O-ring supplied

Hobby Heaven Zephyr Rear Control Knob (HHA-3302) – Preset Paint Flow Limiter with O-Ring

£3.29
Sale price  £3.29 Regular price 
Taxes included. Shipping calculated at checkout.

In stock · same-day dispatch before 3pm

  • Store rating 4.9/5 · 2224 reviews
  • UK tracked delivery
  • Spare Part
  • Zephyr
  • Control Knob

DWG · Product Information

PROJ: HHA-3302 · SHEET 2 / 4

View · Overview

Product overview

HHA-3302 is the fluted knob screwed into the very back of a Hobby Heaven Zephyr. It threads into the open end of the cutaway handle and acts as an end stop on the trigger's rearward stroke. In a dual-action design, that stroke sets how far the needle withdraws from the nozzle, so the knob caps the most paint a full pull can deliver. Wind it in for a tight maximum, handy for repeated fine lines or highlights; wind it out and the whole range returns. It limits paint only: air pressure stays wherever your regulator puts it.

  • Turned with the fingers, no tools needed
  • Rubber O-ring fitted; its light friction helps the knob keep a setting
  • Hollow front shaft that meets the needle drive inside the handle
  • Works at either nozzle size, 0.3 or 0.5 mm; made for the Zephyr alone
  • Packed in a Hobby Heaven blister, HHA-3302 and barcode on the label

Setting a limit

Begin with the knob backed well out. On scrap card, draw the trigger back until the spray gives you the result you want to reproduce, hold it there and wind the knob in until it meets the trigger's travel and stops it. Release, test again and adjust a fraction either way. A lighter pull than the preset still works whenever you want one; to remove the limit, unwind the knob until it stops touching anything.

Knob, or something else?

What happens Try this
Air but little or no paint, even at full pull Knob wound in too far: back it out a few turns before replacing anything
The setting creeps while you work O-ring worn or gone; a new knob comes with one fitted
Bent, burred, or will not start straight Replace the knob; if a new one also refuses, check the handle (HHA-3301)
Knob lost Replace it; until then the airbrush works, just without a preset
Trigger moves, needle stays still The chucking nut (HHA-3202) is loose; the knob is not involved

Signs it needs replacing

A bend from a drop onto the tail, a flattened or crossed thread, a knob that drifts off its setting even with a sound O-ring, or one that has gone missing.

Fitting and care

Disconnect the air, unscrew any old knob from the tail of the handle, check the O-ring on the new one, start it square and give it a few turns, then set it as above. Fingers only, and no force when it reaches either stop. If you strip the airbrush down to clean it, back the knob out first or remember where it sat. Confirmed for the Hobby Heaven Zephyr and nothing else. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.

Notes · Q & A

Which parts fit the Zephyr, and will they fit another airbrush?

Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.

How do I find the right part number?

Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.

Can the Zephyr spray at 0.5 mm?

Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.

How does the Zephyr connect to my compressor?

The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.

What are the seals made of, and how should I clean the parts?

Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.

Notes · Logistics

Shipping

Orders placed before 3pm (Mon–Fri) are dispatched the same day. UK delivery is by Royal Mail 24 Tracked. Free UK delivery on orders over £70. International delivery available via Royal Mail International Tracked or courier.

Returns

If you're not happy with your purchase, contact us within 30 days for a full refund or exchange. Items must be unused and in original packaging.

Table · Specification

Technical specifications

Product details
Brand
Hobby Heaven
Product code
HHA-3302
Type
Accessories
Shipping weight
100 g
Barcode
5061001183364
Made in
China
Materials & finish
Format
Control knob
Usage & compatibility
Compatible with
Hobby Heaven Zephyr
Other parts
Also in this range
Zephyr airbrush system

Product

Hobby Heaven Zephyr Rear Control Knob (HHA-3302) – Preset Paint Flow Limiter with O-Ring

Code (proj)

HHA-3302

Ship. weight

100 g

Brand

Hobby Heaven

Hobby Heaven · By hobbyists, for hobbyists

Sheet 2 / 4

End of sheet

Complete The Job