Hobby Heaven Airbrush Cleaning Brush Set, 5 pcs (HHA-7201)
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2224 reviews
- UK tracked delivery
- Cleaning
- Accessory
DWG · Product Information
PROJ: HHA-7201 · SHEET 2 / 4
View · Overview
Product overview
HHA-7201 is a set of five spiral brushes for the places a rinse leaves dirty. Paint clings wherever it flows slowly: the channel leading from the cup to the nozzle, the cup floor, the insides of caps and fittings. Every brush carries bristles wound onto a twisted wire stem, the heads step up in five sizes, and a single key ring holds the set together. The set suits airbrush cleaning in general rather than one model; on the Hobby Heaven Zephyr it reaches the paint channel, the 7 ml cup and both caps.
- Five brushes, five head sizes
- Bristles wound onto twisted wire stems
- One key ring keeps the smallest from going missing
- Paint channel, cup, caps and fittings
- Hobby Heaven bag labelled HHA-7201, with barcode
Picking a size
Use the largest head that slides in without force, as it scrubs more of the wall per stroke. The slimmest suit the paint channel and small fittings, the mid sizes the caps and the cup-to-body joint, the stoutest the cup interior and outlet.
How to use them
Run cleaner through until the spray is clear, then withdraw the needle so no brush can bend its point. Dip a brush in cleaner, guide it into the cup outlet and twist it along the channel, in and out, until it emerges clean. Treat the cup and caps the same way, flush again to carry off whatever came loose, and put the needle back. The nozzle is the exception: remove it first (the Zephyr's wrench is HHA-7101) and use just the slimmest brush, from the back where the opening is wide. Stop when you feel resistance and never force bristles out through the tip; a soak is gentler on it.
Dirt, or something else?
| Symptom | Probable cause |
|---|---|
| Air but no paint | Dried paint inside: soak, then scrub the channel |
| Spatter on the first pass after a clean | Moisture still inside the airbrush or line: blow air through and empty the moisture trap |
| Cup bubbling | Nozzle or cap not snug; scrubbing changes nothing |
| Spray to one side or split in two | Bent needle point or damaged nozzle, which a brush cannot mend |
| Brush will not enter | Head too large for the hole: go one size down |
Care and replacing
Rinse each brush before paint sets on it and hang it back on the ring. A bent stem can be straightened by hand. On polished surfaces keep them wet with cleaner, since a dry wire stem may scuff them. Once the bristles are flattened or caked with paint that no longer washes out, replace the set.
Worth knowing
Brushes scrub; for a hard plug of paint or a blocked lid vent, the cleaning needle set (HHA-7202) does the poking. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
- Nozzle wrench
- Cleaning brushes
- Cleaning needles
- Nozzle reamer
Product
Hobby Heaven Airbrush Cleaning Brush Set, 5 pcs (HHA-7201)
Code (proj)
HHA-7201
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet