Hobby Heaven Zephyr 0.5mm Nozzle Cap (HHA-2302) – Replacement Airbrush Spare
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Spare Part
- Zephyr
- Nozzle Cap
DWG · Product Information
PROJ: HHA-2302 · SHEET 2 / 4
View · Overview
Product overview
Once a Zephyr runs at 0.5 mm, thanks to the HHA-2002 set, its front end needs the larger nozzle cap, and this is that cap on its own. It is the knurled, polished piece the nozzle sits inside, with an opening matched to the 0.5 mm nozzle so the air surrounds the heavier flow evenly. Painters move to the 0.5 mm setup for primer, varnish and metallic paints. Order this one when a cap is lost, dented or will not seat, and the nozzle and needle behind it are undamaged.
- Sized for nozzle HHA-2102 (0.5 mm)
- One of the four parts of conversion set HHA-2002
- Ridged rim, so you can turn it with your fingers rather than a tool
- Packed in foam inside a labelled 0.5mm tube with a screw lid
- Needle cap HHA-2402 (0.5 mm) screws onto its front
What the cap does
Air leaving the Zephyr passes the nozzle tip inside this cap, and the cap’s opening decides how evenly it surrounds that tip. A 0.5 mm nozzle wants the 0.5 mm opening; a 0.3 mm cap on a 0.5 mm Zephyr will not spray properly.
Is it really the nozzle cap?
| Symptom | Part |
|---|---|
| Front edge bent, threads rough, or the cap has gone missing | This 0.5 mm cap, HHA-2302 |
| Chip or split where the nozzle narrows to its point | 0.5 mm nozzle, HHA-2102 |
| Needle point curled over | 0.5 mm needle, HHA-2202 |
| More than one part damaged in a drop | Set HHA-2002 (the whole 0.5 mm front end) |
Inspect the nozzle under magnification after any fall: damage to the cap often travels inward.
When to change it
Look for a burr or flattened patch on the rim, a thread that binds or lets the cap sit askew, and a pattern that leans one way despite a healthy nozzle and needle. Before blaming the part, rule out dried paint by soaking the cap in cleaner and scrubbing inside with a soft brush, such as one from the HHA-7201 set. If the fault remains, swap it.
Fitting
With the air line disconnected and the nozzle already seated firmly, offer the cap up square and turn it by hand. Stop and restart if the thread catches rather than forcing it, since cross-threading harms the body. Finger-tight holds it; leave the wrench for the nozzle.
Worth knowing
To return to 0.3 mm, fit the 0.3 mm cap HHA-2301 with its matching nozzle and needle, or the complete HHA-2001 set. Both sizes look much the same at a glance, so store whichever cap is off the airbrush in its labelled tube. Its fit is confirmed on the Hobby Heaven Zephyr alone; on any other airbrush, assume it will not fit. Each Zephyr part carries its own HHA number, and new parts keep joining the system under the same numbering.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Zephyr 0.5mm Nozzle Cap (HHA-2302) – Replacement Airbrush Spare
Code (proj)
HHA-2302
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet