Hobby Heaven Zephyr 0.3mm Nozzle (HHA-2101) – Replacement Airbrush Nozzle with O-Ring
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2224 reviews
- UK tracked delivery
- Spare Part
- Zephyr
- 0.3mm
- Nozzle
DWG · Product Information
PROJ: HHA-2101 · SHEET 2 / 4
View · Overview
Product overview
HHA-2101 covers the 0.3 mm nozzle of the Hobby Heaven Zephyr, the size the airbrush ships with. It is the small threaded piece screwed into the nose of the body, and the needle tip sits in it. Draw the trigger back and the needle retracts from the opening, letting paint through to meet the air; release it and the needle closes the opening again. That thin tip is easy to split with over-enthusiastic wrench work or a needle rammed home. If your needle and caps are still sound, this one part is all the repair needs.
- 0.3 mm: the Zephyr’s standard size, as supplied
- Rubber O-ring already fitted on the thread
- Screws into the body; fitted and removed with the Zephyr nozzle wrench (HHA-7101)
- Packed in a transparent screw-cap pot lined with foam, sealed in a blister labelled HHA-2101
Is it really the nozzle?
| What you notice | Likely cause | What to get |
|---|---|---|
| Under a magnifier the tip shows a crack, chip or flared edge | Damaged nozzle | This nozzle |
| Needle point bent or hooked, nozzle opening clean and round | Needle | 0.3 mm needle HHA-2201 |
| Bubbles appear in the cup as you spray | Air leaking round a loose nozzle or a tired O-ring | Snug it up; replace if bubbles persist |
| Paint stops or comes in bursts after the airbrush stood unused | Paint dried inside the tip | Soak and clean before buying anything |
| Needle and nozzle both worn out, or a cap gone missing | More than one part | Whole 0.3 mm set HHA-2001 |
Signs it needs replacing
A healthy nozzle has a clean, round opening when viewed through a loupe or zoomed phone camera. A split or splayed edge cannot be cleaned away, and nor can a spray line that drifts sideways once the airbrush is stripped and clean.
Fitting
- Shut off and unplug the air supply, then flush the airbrush clean.
- Take off both caps, loosen the needle chucking nut and ease the needle back clear of the nozzle.
- Undo the worn nozzle using the wrench and check its O-ring has come out too.
- Turn the new one in by hand, then give the wrench only a slight nudge. Over-tightening is how nozzles split.
- Refit the caps, slide the needle forward until it stops in its seat, tighten the chucking nut and check on clean water before paint.
Care
Soak a blocked nozzle, out of the airbrush, in cleaner; never push a pin through it. The reamer HHA-7301 is the last resort, turned gently.
Worth knowing
- Alone, it will not move a Zephyr to 0.5 mm. The needle, the nozzle and the two caps change together: that is the HHA-2002 set.
- Built for the Zephyr alone: we make no claim that it fits any other airbrush.
- One of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Zephyr 0.3mm Nozzle (HHA-2101) – Replacement Airbrush Nozzle with O-Ring
Code (proj)
HHA-2101
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet