Once a Zephyr has been switched to 0.5 mm using the HHA-2002 set, it runs on a 0.5 mm nozzle, and HHA-2102 is that nozzle sold on its own. It screws into the front of the body and forms the opening the needle point closes. With the trigger pulled back the needle withdraws, paint leaves through the bore and the air breaks it up; let go and the needle seals it. A nozzle tip is thin enough to crack under a needle pushed in hard or an extra quarter-turn on the wrench. When only the nozzle is hurt, you replace the nozzle and keep everything else.
0.5 mm bore, for a Zephyr running on the HHA-2002 conversion parts
Comes with its rubber O-ring in place
Threaded fit, tightened and removed with the nozzle wrench HHA-7101, which is also in the Zephyr box
Ships in a clear pot, labelled 0.5 mm and padded with foam, sealed under a blister that carries the part number
Is it really the nozzle?
Symptom
Probable cause
Order
Cracked, nicked or opened-out tip seen up close
The nozzle itself
HHA-2102
Kinked needle point while the nozzle looks fine
The needle
0.5 mm needle HHA-2202
Air bubbling back into the cup during spraying
Nozzle not snug, or a perished O-ring
Tighten gently and retest, then replace
Spray splutters after a break and nothing looks damaged
Paint dried inside the bore
Strip and clean first
Still on the original 0.3 mm parts, or several 0.5 mm parts damaged
A whole size change is needed
The HHA-2002 set
Signs it needs replacing
Look straight at the tip through a loupe or a zoomed phone camera: the hole should be round with an even rim, and damage to that rim is permanent.
Fitting
Air off, airbrush emptied and cleaned.
Remove both caps. Slacken the needle chucking nut and pull the needle back until its point is out of the nozzle.
Unscrew the nozzle with the wrench, making sure the O-ring came away with it.
Fit the new nozzle finger-tight plus a slight nudge of the wrench, no more.
Caps back on, needle eased forward until it just seats, chucking nut tightened. Check it on water before loading paint.
Care
A 0.5 mm bore still blocks. Soak the nozzle off the airbrush in cleaner instead of probing it; the reamer HHA-7301 comes in only if soaking fails, turned and never pushed. Keep spares in the container.
Worth knowing
This nozzle alone does not convert a 0.3 mm Zephyr. The 0.5 mm needle and caps have to come with it, which is why the HHA-2002 set exists.
Built for the Zephyr alone: we make no claim that it fits any other airbrush.
One of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.
03
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?+
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?+
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?+
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?+
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?+
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
04
Notes · Logistics
Shipping
Orders placed before 3pm (Mon–Fri) are dispatched the same day. UK delivery is by Royal Mail 24 Tracked. Free UK delivery on orders over £70. International delivery available via Royal Mail International Tracked or courier.
Returns
If you're not happy with your purchase, contact us within 30 days for a full refund or exchange. Items must be unused and in original packaging.