HHA-2201 gives you the 0.3 mm needle for the Hobby Heaven Zephyr. Its tapered point sits in the 0.3 mm nozzle: pulling the trigger back draws it away from the opening to let paint out, and releasing the trigger closes the flow. Needles get bent more than anything else on an airbrush, from a drop, a careless wipe or a rushed reassembly. Each Zephyr leaves us with a spare of this size in the box; HHA-2201 replaces that spare once it is used, so a bent point never has to end a painting session.
Needle size 0.3 mm, for the nozzle fitted to every new Zephyr
The same size as the spare supplied with the airbrush
Shipped inside a clear tube printed 0.3, bedded in foam within its box
Goes in through the nose of the airbrush, after the nozzle comes out
Is it really the needle?
What you see
Cause
What to order
Point bent or hooked; it snags when drawn lightly over a fingernail
Bent needle
This needle
The needle wobbles instead of rolling true on a flat table
Bent shaft
This needle
Split nozzle tip, paint escaping with the trigger at rest
Nozzle
0.3 mm nozzle HHA-2101
A new needle is in and the spray is still poor
Nozzle damaged as well
The 0.3 mm set HHA-2001
Spatter straight after a long session
Dried paint on the point
Clean it, then judge
Signs it needs replacing
Clean off any dried paint before judging, because a crusted point sprays just as badly as a bent one. Then roll the needle across a flat surface and look at the point under magnification: it should taper to a single straight tip. A hook or a curve will never close the nozzle evenly again.
Fitting
Unplug the air hose and flush the airbrush through first.
Remove the caps and take the nozzle out with the wrench, then loosen the needle chucking nut. The old needle comes out from the front.
Slide the new needle in from the front, refit the nozzle and caps, then move the needle forward softly until it rests in the nozzle. Forcing it can split the nozzle.
Tighten the chucking nut and try it on clean water first.
Care
An airbrush lying flat on the desk is easily knocked, so rest it in a holder between coats. Hold on to the tube; it is where the next spare should live.
Worth knowing
A Zephyr converted with HHA-2002 runs a 0.5 mm needle, HHA-2202. Keep this one to the 0.3 mm nozzle and caps, never mixed with 0.5 mm ones.
Built for the Zephyr alone: we make no claim that it fits any other airbrush.
One of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.
03
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?+
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?+
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?+
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?+
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?+
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
04
Notes · Logistics
Shipping
Orders placed before 3pm (Mon–Fri) are dispatched the same day. UK delivery is by Royal Mail 24 Tracked. Free UK delivery on orders over £70. International delivery available via Royal Mail International Tracked or courier.
Returns
If you're not happy with your purchase, contact us within 30 days for a full refund or exchange. Items must be unused and in original packaging.