Look through the cutaway handle of the Hobby Heaven Zephyr and the small knurled part at the back is this nut. It screws onto the needle chucking guide's split tail; tightening it squeezes that end around the needle, so needle and guide move as one with every pull of the trigger. When it slackens, the trigger still travels but the needle stays where it is and nothing sprays. Because it comes off at every needle clean, it ranks among the easiest parts to lose.
Diamond-knurled grip, tightened and loosened with fingers
Internal thread matching the guide (HHA-3201)
Small rear opening for the needle tail: the needle can be adjusted while the nut is merely slackened
Shipped in a clear vial with a screw cap and foam insert, inside a blister marked HHA-3202
One nut for both the 0.3 mm and 0.5 mm builds; made for the Zephyr
Nut, or something else?
Sign
What to check
Nut lost
This part
Trigger moves, needle stays still
Nut slack: snug it up firmly with fingers, usually no part needed
Spins without biting or will not start square
Damaged thread: this part, and look over the guide's thread too
Nut tight and undamaged, needle still slips
Worn guide tail: guide (HHA-3201)
Paint flows before the trigger comes back
Needle clamped before it seated: slacken, let it settle into the nozzle, retighten
Trigger floppy, no return
Look at the guide (HHA-3201) or spring case (HHA-3203) instead
Signs it needs replacing
It has gone missing, spins without ever biting, only starts at an angle, or the knurling is flattened and the nut squashed or split, which pliers usually cause. One that has simply loosened only needs tightening.
Fitting
Air off, handle unscrewed. Check that the needle is fitted and resting lightly in the nozzle, not forced. Start the nut square on the guide's threaded tail with your fingers, snug it up firmly, pull the trigger back to watch the needle follow, then screw the handle back on.
Worth knowing
Hang on to the vial: it is the natural home for the nut while the handle is off. Seat the needle first and tighten afterwards, never the other way round. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
03
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?+
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?+
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?+
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?+
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?+
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
04
Notes · Logistics
Shipping
Orders placed before 3pm (Mon–Fri) are dispatched the same day. UK delivery is by Royal Mail 24 Tracked. Free UK delivery on orders over £70. International delivery available via Royal Mail International Tracked or courier.
Returns
If you're not happy with your purchase, contact us within 30 days for a full refund or exchange. Items must be unused and in original packaging.