Hobby Heaven Inline Airbrush Moisture Trap (HHA-5301) – 1/8" BSP, 5 Micron
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2224 reviews
- UK tracked delivery
- Maintenance
- Accessory
DWG · Product Information
PROJ: HHA-5301 · SHEET 2 / 4
View · Overview
Product overview
HHA-5301 is a compact inline moisture trap fitted right at the airbrush: it threads onto the air inlet, the hose threads onto it, and air flows through the trap a moment before entering the airbrush. As compressed air travels down a hose it cools, and part of its water vapour turns back to liquid; when that reaches the nozzle it spits or leaves wet spots in the paint. Inside, a filter element rated at 5 microns stops water droplets and fine dirt, which gather in a clear polycarbonate bowl in plain view. Pushing the spring-loaded pin empties it with nothing unscrewed.
- Airbrush side: 1/8" BSP female, in a polished cap
- Hose side: 1/8" BSP male
- A 5-micron element filters the air
- Push-pin drain that empties the bowl in place
- Pictured on the Zephyr; suits other 1/8" BSP airbrushes and hoses
Moisture, or something else?
| What you see | Likely cause and remedy |
|---|---|
| Clear water spitting out, more so in long sessions or damp weather | Moisture: empty this trap and any trap on the compressor |
| Splatter at the start of strokes, or a grainy pattern | Usually the paint: thin it and wipe the needle tip clean |
| Hiss at either threaded joint | Snug it by hand; tape the male thread if it carries on |
| Drain pin hissing | Debris under the pin: press and release it repeatedly under air |
| Water still gets through | It only stops water that is already liquid: empty it more often and keep a compressor-side trap as well |
Airbrush end or compressor end?
A regulator trap on the compressor handles water produced in the compressor and its tank, not moisture that forms afterwards along the hose; a trap at the airbrush covers that final stretch. With quick disconnects it can stay on the airbrush (plug HHA-5102 screwed onto the trap) or on the hose (coupler HHA-5101 or HHA-5104 on the trap). Whichever you choose, keep the drain pin on the low side while you paint.
Fitting and care
Shut off the air and take the hose off the airbrush. Turn the trap's cap onto the inlet by hand, then the hose onto the trap. With air restored, press the pin once, and dab soapy water on both connections. Empty it before and after every session. Keep thinners and airbrush cleaner away from the bowl, since solvents can craze or split polycarbonate; a bowl that is cracked or permanently cloudy, or a pin that keeps leaking, means a new trap.
Worth knowing
It is not an air dryer: it cuts the risk of water landing in your paint rather than making the air fully dry. Iwata, Harder & Steenbeck, Sparmax, Grex and Master airbrushes take it directly; Badger, Paasche and Aztek each require their own brand's adapter. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Inline Airbrush Moisture Trap (HHA-5301) – 1/8" BSP, 5 Micron
Code (proj)
HHA-5301
Ship. weight
230 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet