Hobby Heaven Zephyr Trigger Main Lever (HHA-3101) – Replacement Airbrush Spare
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2224 reviews
- UK tracked delivery
- Spare Part
- Zephyr
- Lever
DWG · Product Information
PROJ: HHA-3101 · SHEET 2 / 4
View · Overview
Product overview
On the Hobby Heaven Zephyr, everything you spray starts at this lever. Press it and the lower pin opens the air valve; rock it back and it pulls the needle drive rearwards, so the needle leaves its seat and paint joins the airflow. A small hinge between stem and pin lets the button tilt while the pin still holds the valve open. Nothing but the needle keeps the trigger in its slot, so with the needle taken out for cleaning it simply falls free, and a lost trigger is the commonest reason to order this part.
- A complete lever: grooved button, stem, hinge and pin, nothing to assemble
- Same part whether your Zephyr is set up for 0.3 mm or carries the HHA-2002 0.5 mm set
- Built for the Hobby Heaven Zephyr; fit on other airbrushes is not confirmed
- Blister label: HHA-3101 and barcode
Is the trigger really the problem?
| Symptom | Where to look |
|---|---|
| Lever gone, or it dropped out during cleaning | This trigger |
| Stem bent, hinge loose, pin bent or burred | This trigger |
| Lever stays down or returns slowly | Clean away dried paint first; if no better, the air valve (HHA-3401) |
| Air hisses with the lever at rest | Air valve (HHA-3401) failing to close |
| Lever travels back, needle stays put | Loose chucking nut (HHA-3202) |
| Lever floppy, no return | Guide (HHA-3201) went back crooked; refit it |
Signs it needs replacing
Time for a new one when the stem leans instead of standing upright, the hinge rocks sideways, the pin is bent or worn so air arrives at a different point on every press, or the button has worked loose. Stickiness alone almost never means wear.
Fitting
Keep the parts diagram from the quick start guide to hand and disconnect the air. Take off the handle, slacken the chucking nut, unscrew the nozzle and pull the needle forward out of the front. Remove spring case and knob, then the spring and guide. Set the new trigger in pin-first, resting on the valve. Reassemble in reverse order: guide plate behind the trigger, spring, spring case and knob, needle from the front, nozzle and caps. Ease the needle forward until it meets the nozzle, finger-tighten the chucking nut and test air and needle travel without paint.
Worth knowing
Most triggers go missing during cleaning: with the needle out, keep the airbrush upright or park the trigger in a dish. Wipe paint off the body before it can creep into the trigger slot, and keep the air valve away from solvent soaks and ultrasonic cleaners. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Zephyr Trigger Main Lever (HHA-3101) – Replacement Airbrush Spare
Code (proj)
HHA-3101
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet