Hobby Heaven Zephyr Air Valve (HHA-3401) – Complete Assembled Replacement Valve
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Spare Part
- Zephyr
- Air Valve
DWG · Product Information
PROJ: HHA-3401 · SHEET 2 / 4
View · Overview
Product overview
HHA-3401 is the air valve of the Hobby Heaven Zephyr, the unit beneath the trigger that your hose connects to. It is the airbrush's air switch: a spring holds a small piston shut until the trigger presses the valve pin down, air then rises through the airbrush towards the nozzle, and the moment you let go the spring shuts it off. It arrives as a single assembled unit with its O-ring, spring, piston and pin already in place, and one valve suits the Zephyr with either nozzle size, 0.3 mm or 0.5 mm.
- Complete and assembled, ready to screw in
- Rubber O-ring fitted to seal the joint with the airbrush body
- Knurled collar for fitting and removing it by hand
- Lower end is the Zephyr's air inlet, 1/8" BSP male, taking a hose directly or a quick-disconnect plug
- Zephyr only; sold in a Hobby Heaven blister marked HHA-3401
Valve, or something else?
| Sign | Probable cause, then remedy |
|---|---|
| Air keeps coming after you release the trigger | Valve not sealing, often paint or solvent inside: dry it, clean it and lubricate lightly before replacing |
| Trigger stays down or rises slowly | Usually the same sticky valve; clean first, replace if it persists |
| Hiss around the top of the valve | Snug it by hand and inspect its O-ring; replacements arrive with a fresh one |
| Hiss at the hose joint below | The hose fitting or a quick-disconnect (HHA-5103) is leaking, not the valve; brush soapy water over the joint to find it |
| No air at all | First rule out the supply: compressor, regulator, hose; if air gets as far as the airbrush and stops, suspect the valve |
| Air arrives, paint does not | Look at the chucking nut (HHA-3202) or rear knob (HHA-3302) |
Signs it needs replacing
Leaking at rest or sticking after a proper clean and light lubrication, a bent pin, a damaged thread, or solvent damage that has not settled once the valve dried out.
Fitting
Switch the compressor off and take the hose or coupler off the valve. Unscrew the old valve by its collar, confirm the O-ring is on the new one and run it in straight by hand until snug; no force or pliers are needed for it to seal. With no air connected, work the trigger several times to check it moves down freely and springs back, then reconnect: the air should stop the instant the trigger rises, with no hiss at the valve.
Worth knowing
Keep the valve out of solvent baths: thinner swells its rubber seals, the commonest reason a valve sticks. Take it out before you soak the body. A sticky valve needs only a drop of airbrush lubricant, never machine oil or penetrating spray. Its fit is confirmed on our Zephyr only. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Zephyr Air Valve (HHA-3401) – Complete Assembled Replacement Valve
Code (proj)
HHA-3401
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet