Hobby Heaven Airbrush Quick Disconnect Set with Air Flow Valve (HHA-5104) – 1/8" BSP
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Accessory
- Quick Disconnect
DWG · Product Information
PROJ: HHA-5104 · SHEET 2 / 4
View · Overview
Product overview
HHA-5104 is a quick-disconnect set with a second job built in. The plug lives on the airbrush and the coupler on the hose; they click together and part like any quick-disconnect, and the coupler shuts the air off once the plug is out. On the coupler sits a small knurled knob: an air flow valve, the kind often called a MAC valve, which turns the air down at your hand instead of at the compressor. Put the regulator at the session's top pressure, trim down for fine lines, stippling or thin coats, and open fully to flush cleaner.
- Coupler with air flow valve: male 1/8" BSP thread, lives on the hose
- Plug: 5 mm nipple and female 1/8" BSP thread, lives on the airbrush
- Knob trims the air from fully open down to fully shut
- Spring-loaded sleeve releases the plug; air shuts off while it is out
- Both parts packed in a Hobby Heaven blister, HHA-5104 on the label
What the valve can and cannot do
All it can do is reduce the air. The knob restricts the flow reaching the airbrush, which softens the spray, but it cannot add pressure beyond what the regulator delivers, and it has no gauge. Turned fully in, it stops the air altogether. The regulator gauge reads the pressure before the valve, so judge a trimmed setting by spraying a test card. Painters who rarely touch their pressure mid-session may prefer the cheaper plain set, HHA-5103, for the quick-release alone.
Valve set, or something else?
| Problem | Fix |
|---|---|
| No air reaching the airbrush | Knob wound fully in: open it, then make sure the plug has clicked home |
| Weak spray although the regulator is up | Valve half shut: open it fully and spray again first |
| Hiss at a thread | Unsealed joint: thread-sealing tape on the male thread, then refit by hand |
| Hiss round the knob at every setting | Valve seal worn: replace the set |
| One half refuses to thread on | Wrong thread on the airbrush or hose; Badger, Paasche or Aztek gear needs an adapter first |
Fitting
Compressor off, hose bled. Tape the coupler's thread and run it into the hose by hand; tape the airbrush inlet and fit the plug the same way. Open the knob, restore the air, click the plug in and test each joint with a dab of soapy water, then set the regulator and fine-tune with the knob.
Worth knowing
This set is not part of the Zephyr box, which comes with the plain pair. If you run several airbrushes, add an HHA-5102 plug for each one. Iwata, Harder & Steenbeck, Sparmax, Grex, Master and the Zephyr share the 1/8" BSP fitting this set is made for. Fingers only on the knob; never force it. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
- Quick-disconnect coupler
- Quick-disconnect plug
- Quick-disconnect set
- Quick-disconnect set with air valve
- 1.8 m braided hose
- 3 m braided hose
- Moisture trap
- Thread adapter set
Product
Hobby Heaven Airbrush Quick Disconnect Set with Air Flow Valve (HHA-5104) – 1/8" BSP
Code (proj)
HHA-5104
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet