Hobby Heaven Airbrush Quick Disconnect Coupler, Female (HHA-5101) – 1/8" BSP
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Accessory
- Quick Disconnect
DWG · Product Information
PROJ: HHA-5101 · SHEET 2 / 4
View · Overview
Product overview
HHA-5101 is the hose half of a quick-disconnect air connection, a socket that stays screwed to the end of your airbrush hose. A small plug fitted to the airbrush (HHA-5102) pushes into it and locks with a click; pull the knurled sleeve back to free the airbrush. While the socket is empty, a valve inside it stays closed, so the hose stays silent and the compressor can keep running as you change airbrushes or take one to the sink. It has no air flow valve, and it is exactly the coupler packed with the Hobby Heaven Zephyr.
- 1/8" BSP male thread at its base, for a hose with a 1/8" BSP female end
- Accepts standard 5 mm plugs made for airbrush quick-disconnects
- Air cuts off automatically the moment the plug is withdrawn
- Spring-loaded knurled release sleeve, plus a hex for holding it with a spanner
- One coupler in a Hobby Heaven blister labelled HHA-5101; plug not included
Coupler, or something else?
| You notice | Cause and cure |
|---|---|
| A hiss at the hose joint | Thread unsealed: add a few turns of thread-sealing tape and refit by hand |
| A hiss at the click joint although the plug is locked | The internal seal has worn out: fit a new coupler |
| No air although the plug is in | Plug short of the click, so the shut-off is still closed: press it fully home |
| Plug won't lock, or drops out | Grit in the sleeve: clean it, and replace the coupler if that fails |
| It will not start in your hose | A different fitting: Badger, Paasche or Aztek hoses take a brand adapter first |
Signs it needs replacing
A hiss at the click joint even with the plug pushed fully home, a sleeve that sticks or no longer holds the plug, air escaping from the hose with nothing connected, or a thread bent or crushed by a drop.
Fitting
Compressor off, hose bled. Unscrew the hose at the airbrush, wind thread-sealing tape onto the coupler's thread, short of the end, and turn the coupler in by hand until it stops; the hex is only for holding a stubborn fitting. Fit a plug to the airbrush, restore the air, click it in and dab soapy water on every joint: bubbles give a leak away.
Worth knowing
The arithmetic is one coupler for each hose and a plug for each airbrush. The coupler regulates nothing: open with a plug fitted, shut without; for air control at your hand, see the valved set HHA-5104. Iwata, Harder & Steenbeck, Sparmax, Grex, Master and plenty of other hobby brands build to this 1/8" BSP thread, as does the Zephyr, and our hoses HHA-5201 and HHA-5202 and moisture trap HHA-5301 accept it directly. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Airbrush Quick Disconnect Coupler, Female (HHA-5101) – 1/8" BSP
Code (proj)
HHA-5101
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet