Hobby Heaven Airbrush Nozzle Cleaning Reamer (HHA-7301) – with Screw-On Cap
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Cleaning
- Accessory
DWG · Product Information
PROJ: HHA-7301 · SHEET 2 / 4
View · Overview
Product overview
HHA-7301 is a nozzle reamer: a slender taper with cutting edges along it, held in a grooved, gold-finish metal handle and closed by a screw-on cap. Paint that dries inside a nozzle tends to settle right at the tip, the narrowest opening in the whole airbrush, where a brush cannot reach. Eased into a removed nozzle and rotated, the edges shave that ring of dried paint away. It is a last resort rather than an everyday tool.
- Slender tapered tip with cutting edges
- Grooved handle for a light, controlled grip
- Screw-on cap that guards the point and your fingers
- For dried paint inside a nozzle taken out of the airbrush
- Hobby Heaven bag labelled HHA-7301, with barcode
Before you reach for it
Most blocked nozzles clear without anything touching the inside. Remove the nozzle (HHA-7101 is the wrench for the Zephyr) and leave it in airbrush cleaner: minutes for fresh paint, longer for old. Look through it towards a lamp; a clean, round opening means it can go back in. Only if paint is still visible is the reamer needed.
Using it
Unscrew the cap, hold the nozzle lightly, and slide the point into the opening until it just meets resistance. Then roll the handle slowly between finger and thumb a few times each way, with no pressure behind it, and let the edges remove the paint. Withdraw, wipe, hold it up to the lamp again and go back in only if needed. Rinse the nozzle before refitting it. Turn, never push: forcing the taper deeper stretches or splits the opening, and a damaged nozzle has to be replaced.
Reaming, or something else?
| What happens | Look at this first |
|---|---|
| Air flows, paint does not | A blockage in the nozzle or channel: soak it, and ream only what the soak leaves |
| Spits at the start of every stroke | Often paint on the needle point or around the nozzle cap: clean those first |
| Spray split or pulling sideways | Bent needle point or split nozzle; reaming fixes neither |
| Bubbles appear in the cup | Nozzle or its cap not tight: snug them gently |
| Opening clear and round, yet the spray is poor | Then the nozzle is not the problem; check the needle, both caps and how thin the paint is |
Care
After each use, wipe the point and refit the cap straight away. Do not use it as a scribe or awl on other materials, and avoid dropping it tip first: a bent or dulled point is no good for a nozzle. Store it dry, with the cap fitted.
Worth knowing
The finer the nozzle, the lighter the touch it needs. On the Zephyr a split nozzle is replaced by HHA-2101 (0.3 mm) or HHA-2102 (0.5 mm). This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
- Nozzle wrench
- Cleaning brushes
- Cleaning needles
- Nozzle reamer
Product
Hobby Heaven Airbrush Nozzle Cleaning Reamer (HHA-7301) – with Screw-On Cap
Code (proj)
HHA-7301
Ship. weight
100 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet