Hobby Heaven Zephyr Cutaway Handle (HHA-3301) – Replacement Airbrush Handle with O-Ring
In stock · same-day dispatch before 3pm
- Store rating 4.9/5 · 2225 reviews
- UK tracked delivery
- Spare Part
- Zephyr
- Handle
DWG · Product Information
PROJ: HHA-3301 · SHEET 2 / 4
View · Overview
Product overview
HHA-3301 is the polished tail section of the Hobby Heaven Zephyr, the tube your hand rests on behind the trigger. It threads onto the rear of the body by hand and encloses the needle drive (chucking guide, spring case and chucking nut), shielding it from knocks and overspray. A window in its side lets you check and turn the chucking nut with the handle in place. Handles seldom wear out; they are swapped after a fall dents one, a thread gets crossed or one goes astray. It is the same handle whether your Zephyr runs a 0.3 mm or a 0.5 mm nozzle.
- Rubber O-ring already seated where the thread meets the tube
- Side window onto the chucking nut
- Open tail, threaded inside, that takes the rear knob, HHA-3302
- Built for the Zephyr only, whichever nozzle size it carries
- Comes in a Hobby Heaven box with the HHA-3301 label; knob not included
Handle, or something else?
| Symptom | Remedy |
|---|---|
| Dented, kinked or split after a fall | Replace the handle |
| Will not start straight or binds as it turns | Damaged thread: replace it, and inspect the body's thread too |
| Rattles or unscrews itself | Usually a flat or missing O-ring; a new handle arrives with one fitted |
| Rear knob will not hold or will not go in | Try a new knob (HHA-3302) first; if that fails too, the handle's inner thread is at fault |
| Needle stays put when the trigger moves | A loose chucking nut (HHA-3202), not this part |
| Trigger loose or slow to return | Look at the spring case (HHA-3203) or chucking guide (HHA-3201) instead |
Signs it needs replacing
A kink or dent from landing on its tail, a burred or crossed thread that no longer runs smoothly, an inner thread that can no longer grip the knob, or a handle that has gone missing. Scuffs on the polish are only cosmetic.
Fitting
Disconnect the air first. Turn the old handle off by hand; if the knob sits in its tail, take the knob out and set it aside for the new one. Check that the O-ring sits on the replacement, start it square on the body and turn it until snug, with no tools. On a full rebuild the handle is the last part to go on. Finish by screwing the knob back into the tail.
Worth knowing
Hand pressure is all the thread needs, and forcing it can strip it. Wipe off any paint that reaches the thread while it is still wet. We can only vouch for it on the Zephyr itself: thread and length vary from one airbrush to the next, so treat it as unsuitable for other models. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.
Notes · Q & A
Which parts fit the Zephyr, and will they fit another airbrush?
Needles, nozzles, caps and body parts are made for the Hobby Heaven Zephyr (HHA-1001), and that is the only airbrush we confirm them on. The 7 ml cup and the nozzle wrench may suit other airbrushes, but that is untested. Quick disconnects, hoses, the moisture trap and the thread adapters are universal accessories built around the standard 1/8" BSP airbrush thread, and the cleaning brushes, needles and reamer are general tools. The Compatible with row on each page says which group a part belongs to.
How do I find the right part number?
Every part has its own HHA number, printed on its box. HHA-20xx are matched needle, nozzle and cap sets, 21xx nozzles, 22xx needles, 23xx nozzle caps and 24xx needle caps; a last digit of 1 means 0.3 mm and 2 means 0.5 mm. HHA-3xxx are body parts, 4xxx cups, 5xxx air connections and 7xxx tools and cleaning. The system keeps growing: new parts join under the same numbering, and existing numbers never change meaning.
Can the Zephyr spray at 0.5 mm?
Yes. It comes set up at 0.3 mm, and the HHA-2002 set converts it: a 0.5 mm needle, a 0.5 mm nozzle with its O-ring, a nozzle cap and a needle cap. Those four parts change together, because needle, nozzle and caps must all be the same size. The body parts (HHA-3xxx) are the same for both setups.
How does the Zephyr connect to my compressor?
The air inlet is a 1/8" BSP male thread. Our braided hoses have a 1/8" BSP female nut at both ends, and the quick disconnects take the standard 5 mm hobby plug. Many compressors have a 1/4" BSP outlet and need an adapter; US compressors may have 1/4" NPT, which does not mate with BSP and needs an NPT-to-BSP adapter. Spray at 15–40 PSI and never above 40.
What are the seals made of, and how should I clean the parts?
Every seal in the Zephyr is a rubber O-ring. Flush with airbrush cleaner between colours and strip-clean after a session, but keep the assembled air valve (HHA-3401) out of solvent baths, as its pin, piston, spring and O-ring come as one unit. For a blocked nozzle, soak it out of the airbrush first; the reamer (HHA-7301) is the last resort, turned and never pushed.
Notes · Logistics
Shipping
Returns
Table · Specification
Technical specifications
Product
Hobby Heaven Zephyr Cutaway Handle (HHA-3301) – Replacement Airbrush Handle with O-Ring
Code (proj)
HHA-3301
Ship. weight
230 g
Brand
Hobby Heaven
Hobby Heaven · By hobbyists, for hobbyists
Sheet 2 / 4
End of sheet