{"product_id":"hobby-heaven-zephyr-0-5mm-nozzle-hha-2102","title":"Hobby Heaven Zephyr 0.5mm Nozzle (HHA-2102) – Replacement Airbrush Nozzle with O-Ring","description":"\u003cp\u003eOnce a Zephyr has been switched to 0.5 mm using the HHA-2002 set, it runs on a 0.5 mm nozzle, and HHA-2102 is that nozzle sold on its own. It screws into the front of the body and forms the opening the needle point closes. With the trigger pulled back the needle withdraws, paint leaves through the bore and the air breaks it up; let go and the needle seals it. A nozzle tip is thin enough to crack under a needle pushed in hard or an extra quarter-turn on the wrench. When only the nozzle is hurt, you replace the nozzle and keep everything else.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.5 mm bore, for a Zephyr running on the HHA-2002 conversion parts\u003c\/li\u003e\n\u003cli\u003eComes with its rubber O-ring in place\u003c\/li\u003e\n\u003cli\u003eThreaded fit, tightened and removed with the nozzle wrench HHA-7101, which is also in the Zephyr box\u003c\/li\u003e\n\u003cli\u003eShips in a clear pot, labelled 0.5 mm and padded with foam, sealed under a blister that carries the part number\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the nozzle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eProbable cause\u003c\/th\u003e\n\u003cth\u003eOrder\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eCracked, nicked or opened-out tip seen up close\u003c\/td\u003e\n\u003ctd\u003eThe nozzle itself\u003c\/td\u003e\n\u003ctd\u003eHHA-2102\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKinked needle point while the nozzle looks fine\u003c\/td\u003e\n\u003ctd\u003eThe needle\u003c\/td\u003e\n\u003ctd\u003e0.5 mm needle HHA-2202\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir bubbling back into the cup during spraying\u003c\/td\u003e\n\u003ctd\u003eNozzle not snug, or a perished O-ring\u003c\/td\u003e\n\u003ctd\u003eTighten gently and retest, then replace\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray splutters after a break and nothing looks damaged\u003c\/td\u003e\n\u003ctd\u003ePaint dried inside the bore\u003c\/td\u003e\n\u003ctd\u003eStrip and clean first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStill on the original 0.3 mm parts, or several 0.5 mm parts damaged\u003c\/td\u003e\n\u003ctd\u003eA whole size change is needed\u003c\/td\u003e\n\u003ctd\u003eThe HHA-2002 set\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eLook straight at the tip through a loupe or a zoomed phone camera: the hole should be round with an even rim, and damage to that rim is permanent.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAir off, airbrush emptied and cleaned.\u003c\/li\u003e\n\u003cli\u003eRemove both caps. Slacken the needle chucking nut and pull the needle back until its point is out of the nozzle.\u003c\/li\u003e\n\u003cli\u003eUnscrew the nozzle with the wrench, making sure the O-ring came away with it.\u003c\/li\u003e\n\u003cli\u003eFit the new nozzle finger-tight plus a slight nudge of the wrench, no more.\u003c\/li\u003e\n\u003cli\u003eCaps back on, needle eased forward until it just seats, chucking nut tightened. Check it on water before loading paint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eA 0.5 mm bore still blocks. Soak the nozzle off the airbrush in cleaner instead of probing it; the reamer HHA-7301 comes in only if soaking fails, turned and never pushed. Keep spares in the container.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis nozzle alone does not convert a 0.3 mm Zephyr. The 0.5 mm needle and caps have to come with it, which is why the HHA-2002 set exists.\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr alone: we make no claim that it fits any other airbrush.\u003c\/li\u003e\n\u003cli\u003eOne of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811710653,"sku":"HHA-2102","price":5.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-5mm-nozzle-hha-2102-2.jpg?v=1795190842","url":"https:\/\/hobbyheaven.org\/en-us\/products\/hobby-heaven-zephyr-0-5mm-nozzle-hha-2102","provider":"Hobby Heaven","version":"1.0","type":"link"}