{"title":"Hobby Heaven Zephyr Airbrush, Spares \u0026 Accessories","description":null,"products":[{"product_id":"hobby-heaven-zephyr-0-3-airbrush-hha-1001","title":"Hobby Heaven Zephyr 0.3 Airbrush (HHA-1001) – 0.3mm Gravity-Feed Dual-Action, 7ml Cup","description":"\u003cp\u003eThe Zephyr 0.3 (HHA-1001) is the airbrush that carries the Hobby Heaven name: dual action from a lever on top, gravity fed, mixing paint with air inside the head, in polished chrome with a cutaway handle. A matched 0.3 mm pair of needle and nozzle sits below a lidded 7 ml cup. Each wearing part has its own HHA code and its own listing, so a bent needle or cracked nozzle means one part, not a new airbrush. The HHA-2002 set converts it to 0.5 mm for primer and varnish.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLever down gives air, lever back gives paint; a rear knob caps its travel, not the pressure\u003c\/li\u003e\n\u003cli\u003eAir end threaded 1\/8\" BSP, male\u003c\/li\u003e\n\u003cli\u003eWorks from 15 to 40 PSI; never go higher\u003c\/li\u003e\n\u003cli\u003eEvery seal is a rubber O-ring\u003c\/li\u003e\n\u003cli\u003eBoxed with a spare needle, the nozzle wrench and a quick-disconnect pair\u003c\/li\u003e\n\u003cli\u003eEach order adds a free 80 g tin of our black HHP-1001 masking putty\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn the box, and what you still need\u003c\/h3\u003e\n\u003cp\u003eIn the foam of the presentation box: the airbrush with cup and lid on, a spare needle (0.3 mm) in a clear tube, the nozzle wrench (also sold as HHA-7101), a female quick-disconnect coupler (HHA-5101), the male plug for the airbrush (HHA-5102) and an illustrated quick start guide. Still to find: a compressor fitted with a pressure regulator, paint, cleaner and an air hose. The hose can be ours: HHA-5201 is 1.8 m and HHA-5202 is 3 m, both braided with a female 1\/8\" BSP nut at each end, so either screws straight onto the coupler or the airbrush. Where the compressor outlet is 1\/4\", the adapter set HHA-5401 bridges the gap; an inline moisture trap (HHA-5301) keeps water out.\u003c\/p\u003e\n\u003ch3\u003eIs it really the airbrush?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat happens\u003c\/th\u003e\n\u003cth\u003eUsual cause, and the part\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBubbles rise through the cup\u003c\/td\u003e\n\u003ctd\u003eNozzle loose or its O-ring missing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpitting as a stroke starts\u003c\/td\u003e\n\u003ctd\u003eDry paint on the needle tip, or water in the line\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray pulls sideways or splits\u003c\/td\u003e\n\u003ctd\u003eBent needle point or split nozzle: HHA-2201 or HHA-2101\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir but no paint\u003c\/td\u003e\n\u003ctd\u003eDried paint inside: soak, then brushes HHA-7201\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLever will not draw back far\u003c\/td\u003e\n\u003ctd\u003eRear knob wound in: back it off (spare knob HHA-3302)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCare and fitting\u003c\/h3\u003e\n\u003cp\u003eFlush with cleaner after every session. For a deeper clean, remove the caps, take the nozzle out with the wrench and draw the needle out through the front. Keep the air valve (HHA-3401) out of any solvent bath, as it is one assembled unit with its own O-ring. Refit the nozzle finger-tight, then a fraction more with the wrench, as over-tightening cracks nozzles. Needle and nozzle are matched, so replace them as Zephyr parts, size for size.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThe Zephyr heads a numbered system of parts and accessories that keeps growing. A number never changes meaning, so the HHA code finds the right spare.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68273221370045,"sku":"HHA-1001","price":28.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/Hero1_85a9beec-6b6c-493b-9262-1ab1dadef6e8.png?v=1794487992"},{"product_id":"hobby-heaven-zephyr-0-3mm-needle-nozzle-set-hha-2001","title":"Hobby Heaven Zephyr 0.3mm Needle \u0026 Nozzle Set (HHA-2001) – Matched Needle, Nozzle and Caps","description":"\u003cp\u003eHHA-2001 puts the complete 0.3 mm front end of the Hobby Heaven Zephyr in one box: a needle, a nozzle with its rubber O-ring, the nozzle cap and the needle cap, all in the size the airbrush is built around. Every Zephyr part carries its own HHA number, so when a tip bends or a nozzle cracks you can reorder exactly this set instead of hunting for a generic needle that may never seat. Changing all four together restores the matched pairing, and the Zephyr system keeps growing under the same numbering.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFour parts, one of each, every one of them 0.3 mm\u003c\/li\u003e\n\u003cli\u003eNozzle cap with an external thread, needle cap with an internal one; both have knurled rims for grip\u003c\/li\u003e\n\u003cli\u003eRubber O-ring already fitted to the nozzle\u003c\/li\u003e\n\u003cli\u003ePadded tube for the needle, padded container for the small parts, both set into EVA foam\u003c\/li\u003e\n\u003cli\u003eMade for the Zephyr; we do not claim a fit on any other airbrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the needle and nozzle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you notice\u003c\/th\u003e\n\u003cth\u003eLikely reason\u003c\/th\u003e\n\u003cth\u003eTry first\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray drifts sideways or spits\u003c\/td\u003e\n\u003ctd\u003eBent needle tip or a damaged nozzle\u003c\/td\u003e\n\u003ctd\u003eLook for dried paint at the tip\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint still comes out with the lever all the way forward\u003c\/td\u003e\n\u003ctd\u003eThe needle has stopped closing in the nozzle\u003c\/td\u003e\n\u003ctd\u003eClean the nozzle bore, then inspect the tip\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBubbles rise in the cup while you spray\u003c\/td\u003e\n\u003ctd\u003eAir leaking back because the nozzle is loose or worn\u003c\/td\u003e\n\u003ctd\u003eSnug the nozzle gently, check the O-ring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNozzle tip visibly cracked or chipped\u003c\/td\u003e\n\u003ctd\u003eOvertightening, or the needle forced into it\u003c\/td\u003e\n\u003ctd\u003eNone: a split nozzle cannot be repaired\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eA cap is lost or its thread stripped\u003c\/td\u003e\n\u003ctd\u003eA drop or general wear\u003c\/td\u003e\n\u003ctd\u003eFit new caps\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eDried paint causes most of these symptoms too, so strip and clean first. If the fault survives a proper clean, the parts are worn out.\u003c\/p\u003e\n\u003ch3\u003eFitting the set\u003c\/h3\u003e\n\u003cp\u003eDisconnect the air before you start. Take the handle off, loosen the needle chucking nut, unscrew the nozzle and draw the old needle out through the front. Refit in this order: the new needle in from the front, then the nozzle, screwed in by hand and given only a slight nudge with the wrench, since overtightening splits it. Add both caps, ease the needle forward until it just touches its seat, tighten the chucking nut and put the handle back. No wrench in this box: the Zephyr ships with one, and HHA-7101 is that wrench on its own.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eOnly the needle damaged? The Zephyr's own box carries one extra 0.3 mm needle. Reach for this set when the nozzle or a cap has worn as well. The needle cap is the open crown at the front that guards the needle tip; you can take it off for very close work. Never mix sizes: pushing the 0.5 mm needle into this smaller nozzle ruins the spray and risks damaging both; convert with the HHA-2002 set instead.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811317437,"sku":"HHA-2001","price":7.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-3mm-needle-nozzle-set-hha-2001-1.jpg?v=1795190744"},{"product_id":"hobby-heaven-zephyr-0-5mm-needle-nozzle-set-hha-2002","title":"Hobby Heaven Zephyr 0.5mm Needle \u0026 Nozzle Set (HHA-2002) – 0.5mm Conversion Kit","description":"\u003cp\u003eHHA-2002 turns the Hobby Heaven Zephyr from its stock 0.3 mm into a 0.5 mm airbrush. Inside are the four parts that must change as one: needle and nozzle in 0.5 mm, the nozzle carrying a rubber O-ring, plus the nozzle cap and needle cap made for that size. The opening in the cap must suit the nozzle for the air to wrap around the paint properly, which is why both caps are part of the set. Already using 0.5 mm on your Zephyr? Then the set doubles as the replacement for worn parts.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eOne airbrush, two sizes: stay on the stock size for detail, switch to this set when a job needs more flow\u003c\/li\u003e\n\u003cli\u003eFour parts, one of each, all 0.5 mm, with the O-ring already on the nozzle\u003c\/li\u003e\n\u003cli\u003eKnurled caps: external thread on the nozzle cap, internal thread on the needle cap\u003c\/li\u003e\n\u003cli\u003ePacked in EVA foam, with a padded tube for the needle and a padded container that later stores the idle set\u003c\/li\u003e\n\u003cli\u003eMade for the Zephyr only, with no claim of fit on other airbrushes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eChoosing the size for the job\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003cth\u003eGood for\u003c\/th\u003e\n\u003cth\u003eWhy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e0.5 mm (this set)\u003c\/td\u003e\n\u003ctd\u003ePrimer, varnish of any sheen, metallic and colour-shift paints, basecoats on vehicles, big kits and terrain\u003c\/td\u003e\n\u003ctd\u003eThicker paint and metal flakes pass without clogging, and coverage is quicker\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e0.3 mm (HHA-2001, stock)\u003c\/td\u003e\n\u003ctd\u003eFreehand detail, glazes, fine lines and small figures\u003c\/td\u003e\n\u003ctd\u003eA narrower spray that is easier to control\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThe label on a paint or primer can settle it: some brands print a minimum nozzle size.\u003c\/p\u003e\n\u003ch3\u003eSwapping between sizes\u003c\/h3\u003e\n\u003cp\u003eShut off the air supply and give the airbrush a clean. With the handle removed and the chucking nut slackened, the nozzle unscrews and the needle slides out of the front. Build the other size up in reverse: needle in from the front, nozzle finger-tight with just a touch more from the wrench (forcing it cracks the nozzle), both caps, then let the needle seat gently before the chucking nut and handle go back. You need the Zephyr wrench, HHA-7101, which is not included here. Put the removed parts straight into this box so the two sizes never end up mixed.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eFine detail is not what 0.5 mm is for. Careful lever control still gives a soft line, but fine work is easier back on 0.3 mm with HHA-2001, which is the point of owning both. Swap all four parts at once: the smaller cap over this nozzle, or the larger needle pushed into the smaller nozzle, sprays badly and may ruin the parts. Needle tips bend easily at any size, usually from a fall off the desk or a cloth pulled towards the point, so wipe a needle away from its tip.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811481277,"sku":"HHA-2002","price":7.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-5mm-needle-nozzle-set-hha-2002-1.jpg?v=1795190755"},{"product_id":"hobby-heaven-zephyr-0-3mm-nozzle-hha-2101","title":"Hobby Heaven Zephyr 0.3mm Nozzle (HHA-2101) – Replacement Airbrush Nozzle with O-Ring","description":"\u003cp\u003eHHA-2101 covers the 0.3 mm nozzle of the Hobby Heaven Zephyr, the size the airbrush ships with. It is the small threaded piece screwed into the nose of the body, and the needle tip sits in it. Draw the trigger back and the needle retracts from the opening, letting paint through to meet the air; release it and the needle closes the opening again. That thin tip is easy to split with over-enthusiastic wrench work or a needle rammed home. If your needle and caps are still sound, this one part is all the repair needs.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.3 mm: the Zephyr’s standard size, as supplied\u003c\/li\u003e\n\u003cli\u003eRubber O-ring already fitted on the thread\u003c\/li\u003e\n\u003cli\u003eScrews into the body; fitted and removed with the Zephyr nozzle wrench (HHA-7101)\u003c\/li\u003e\n\u003cli\u003ePacked in a transparent screw-cap pot lined with foam, sealed in a blister labelled HHA-2101\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the nozzle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you notice\u003c\/th\u003e\n\u003cth\u003eLikely cause\u003c\/th\u003e\n\u003cth\u003eWhat to get\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eUnder a magnifier the tip shows a crack, chip or flared edge\u003c\/td\u003e\n\u003ctd\u003eDamaged nozzle\u003c\/td\u003e\n\u003ctd\u003eThis nozzle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle point bent or hooked, nozzle opening clean and round\u003c\/td\u003e\n\u003ctd\u003eNeedle\u003c\/td\u003e\n\u003ctd\u003e0.3 mm needle HHA-2201\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBubbles appear in the cup as you spray\u003c\/td\u003e\n\u003ctd\u003eAir leaking round a loose nozzle or a tired O-ring\u003c\/td\u003e\n\u003ctd\u003eSnug it up; replace if bubbles persist\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint stops or comes in bursts after the airbrush stood unused\u003c\/td\u003e\n\u003ctd\u003ePaint dried inside the tip\u003c\/td\u003e\n\u003ctd\u003eSoak and clean before buying anything\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle and nozzle both worn out, or a cap gone missing\u003c\/td\u003e\n\u003ctd\u003eMore than one part\u003c\/td\u003e\n\u003ctd\u003eWhole 0.3 mm set HHA-2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA healthy nozzle has a clean, round opening when viewed through a loupe or zoomed phone camera. A split or splayed edge cannot be cleaned away, and nor can a spray line that drifts sideways once the airbrush is stripped and clean.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eShut off and unplug the air supply, then flush the airbrush clean.\u003c\/li\u003e\n\u003cli\u003eTake off both caps, loosen the needle chucking nut and ease the needle back clear of the nozzle.\u003c\/li\u003e\n\u003cli\u003eUndo the worn nozzle using the wrench and check its O-ring has come out too.\u003c\/li\u003e\n\u003cli\u003eTurn the new one in by hand, then give the wrench only a slight nudge. Over-tightening is how nozzles split.\u003c\/li\u003e\n\u003cli\u003eRefit the caps, slide the needle forward until it stops in its seat, tighten the chucking nut and check on clean water before paint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eSoak a blocked nozzle, out of the airbrush, in cleaner; never push a pin through it. The reamer HHA-7301 is the last resort, turned gently.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAlone, it will not move a Zephyr to 0.5 mm. The needle, the nozzle and the two caps change together: that is the HHA-2002 set.\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr alone: we make no claim that it fits any other airbrush.\u003c\/li\u003e\n\u003cli\u003eOne of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811579581,"sku":"HHA-2101","price":4.59,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-3mm-nozzle-hha-2101-2.jpg?v=1795190834"},{"product_id":"hobby-heaven-zephyr-0-5mm-nozzle-hha-2102","title":"Hobby Heaven Zephyr 0.5mm Nozzle (HHA-2102) – Replacement Airbrush Nozzle with O-Ring","description":"\u003cp\u003eOnce a Zephyr has been switched to 0.5 mm using the HHA-2002 set, it runs on a 0.5 mm nozzle, and HHA-2102 is that nozzle sold on its own. It screws into the front of the body and forms the opening the needle point closes. With the trigger pulled back the needle withdraws, paint leaves through the bore and the air breaks it up; let go and the needle seals it. A nozzle tip is thin enough to crack under a needle pushed in hard or an extra quarter-turn on the wrench. When only the nozzle is hurt, you replace the nozzle and keep everything else.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.5 mm bore, for a Zephyr running on the HHA-2002 conversion parts\u003c\/li\u003e\n\u003cli\u003eComes with its rubber O-ring in place\u003c\/li\u003e\n\u003cli\u003eThreaded fit, tightened and removed with the nozzle wrench HHA-7101, which is also in the Zephyr box\u003c\/li\u003e\n\u003cli\u003eShips in a clear pot, labelled 0.5 mm and padded with foam, sealed under a blister that carries the part number\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the nozzle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eProbable cause\u003c\/th\u003e\n\u003cth\u003eOrder\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eCracked, nicked or opened-out tip seen up close\u003c\/td\u003e\n\u003ctd\u003eThe nozzle itself\u003c\/td\u003e\n\u003ctd\u003eHHA-2102\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKinked needle point while the nozzle looks fine\u003c\/td\u003e\n\u003ctd\u003eThe needle\u003c\/td\u003e\n\u003ctd\u003e0.5 mm needle HHA-2202\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir bubbling back into the cup during spraying\u003c\/td\u003e\n\u003ctd\u003eNozzle not snug, or a perished O-ring\u003c\/td\u003e\n\u003ctd\u003eTighten gently and retest, then replace\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray splutters after a break and nothing looks damaged\u003c\/td\u003e\n\u003ctd\u003ePaint dried inside the bore\u003c\/td\u003e\n\u003ctd\u003eStrip and clean first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStill on the original 0.3 mm parts, or several 0.5 mm parts damaged\u003c\/td\u003e\n\u003ctd\u003eA whole size change is needed\u003c\/td\u003e\n\u003ctd\u003eThe HHA-2002 set\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eLook straight at the tip through a loupe or a zoomed phone camera: the hole should be round with an even rim, and damage to that rim is permanent.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAir off, airbrush emptied and cleaned.\u003c\/li\u003e\n\u003cli\u003eRemove both caps. Slacken the needle chucking nut and pull the needle back until its point is out of the nozzle.\u003c\/li\u003e\n\u003cli\u003eUnscrew the nozzle with the wrench, making sure the O-ring came away with it.\u003c\/li\u003e\n\u003cli\u003eFit the new nozzle finger-tight plus a slight nudge of the wrench, no more.\u003c\/li\u003e\n\u003cli\u003eCaps back on, needle eased forward until it just seats, chucking nut tightened. Check it on water before loading paint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eA 0.5 mm bore still blocks. Soak the nozzle off the airbrush in cleaner instead of probing it; the reamer HHA-7301 comes in only if soaking fails, turned and never pushed. Keep spares in the container.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis nozzle alone does not convert a 0.3 mm Zephyr. The 0.5 mm needle and caps have to come with it, which is why the HHA-2002 set exists.\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr alone: we make no claim that it fits any other airbrush.\u003c\/li\u003e\n\u003cli\u003eOne of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811710653,"sku":"HHA-2102","price":4.59,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-5mm-nozzle-hha-2102-2.jpg?v=1795190842"},{"product_id":"hobby-heaven-zephyr-0-3mm-needle-hha-2201","title":"Hobby Heaven Zephyr 0.3mm Needle (HHA-2201) – Replacement Airbrush Needle","description":"\u003cp\u003eHHA-2201 gives you the 0.3 mm needle for the Hobby Heaven Zephyr. Its tapered point sits in the 0.3 mm nozzle: pulling the trigger back draws it away from the opening to let paint out, and releasing the trigger closes the flow. Needles get bent more than anything else on an airbrush, from a drop, a careless wipe or a rushed reassembly. Each Zephyr leaves us with a spare of this size in the box; HHA-2201 replaces that spare once it is used, so a bent point never has to end a painting session.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eNeedle size 0.3 mm, for the nozzle fitted to every new Zephyr\u003c\/li\u003e\n\u003cli\u003eThe same size as the spare supplied with the airbrush\u003c\/li\u003e\n\u003cli\u003eShipped inside a clear tube printed 0.3, bedded in foam within its box\u003c\/li\u003e\n\u003cli\u003eGoes in through the nose of the airbrush, after the nozzle comes out\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the needle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you see\u003c\/th\u003e\n\u003cth\u003eCause\u003c\/th\u003e\n\u003cth\u003eWhat to order\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePoint bent or hooked; it snags when drawn lightly over a fingernail\u003c\/td\u003e\n\u003ctd\u003eBent needle\u003c\/td\u003e\n\u003ctd\u003eThis needle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eThe needle wobbles instead of rolling true on a flat table\u003c\/td\u003e\n\u003ctd\u003eBent shaft\u003c\/td\u003e\n\u003ctd\u003eThis needle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSplit nozzle tip, paint escaping with the trigger at rest\u003c\/td\u003e\n\u003ctd\u003eNozzle\u003c\/td\u003e\n\u003ctd\u003e0.3 mm nozzle HHA-2101\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eA new needle is in and the spray is still poor\u003c\/td\u003e\n\u003ctd\u003eNozzle damaged as well\u003c\/td\u003e\n\u003ctd\u003eThe 0.3 mm set HHA-2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpatter straight after a long session\u003c\/td\u003e\n\u003ctd\u003eDried paint on the point\u003c\/td\u003e\n\u003ctd\u003eClean it, then judge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eClean off any dried paint before judging, because a crusted point sprays just as badly as a bent one. Then roll the needle across a flat surface and look at the point under magnification: it should taper to a single straight tip. A hook or a curve will never close the nozzle evenly again.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eUnplug the air hose and flush the airbrush through first.\u003c\/li\u003e\n\u003cli\u003eRemove the caps and take the nozzle out with the wrench, then loosen the needle chucking nut. The old needle comes out from the front.\u003c\/li\u003e\n\u003cli\u003eSlide the new needle in from the front, refit the nozzle and caps, then move the needle forward softly until it rests in the nozzle. Forcing it can split the nozzle.\u003c\/li\u003e\n\u003cli\u003eTighten the chucking nut and try it on clean water first.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eAn airbrush lying flat on the desk is easily knocked, so rest it in a holder between coats. Hold on to the tube; it is where the next spare should live.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eA Zephyr converted with HHA-2002 runs a 0.5 mm needle, HHA-2202. Keep this one to the 0.3 mm nozzle and caps, never mixed with 0.5 mm ones.\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr alone: we make no claim that it fits any other airbrush.\u003c\/li\u003e\n\u003cli\u003eOne of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811841725,"sku":"HHA-2201","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-3mm-needle-hha-2201-2.jpg?v=1795190851"},{"product_id":"hobby-heaven-zephyr-0-5mm-needle-hha-2202","title":"Hobby Heaven Zephyr 0.5mm Needle (HHA-2202) – Replacement Airbrush Needle","description":"\u003cp\u003eRun a Zephyr at 0.5 mm with the HHA-2002 set and it needs a 0.5 mm needle; HHA-2202 is that needle on its own. Its tapered point closes the 0.5 mm nozzle; as you pull the trigger back the needle withdraws and paint flows, and as you let go it shuts off again. The spare needle packed with every Zephyr is 0.3 mm, so a converted airbrush has no back-up of this size until you add one. When the point bends and the nozzle has survived, this is the only part to buy.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.5 mm needle for the Zephyr’s 0.5 mm nozzle (HHA-2102, or the nozzle from the HHA-2002 set)\u003c\/li\u003e\n\u003cli\u003eWill not suit the 0.3 mm nozzle a Zephyr ships with\u003c\/li\u003e\n\u003cli\u003eKept straight in transit by a clear tube printed 0.5, in a box lined with foam\u003c\/li\u003e\n\u003cli\u003eInserted at the nose end once the nozzle is off\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the needle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eProbable cause\u003c\/th\u003e\n\u003cth\u003eFix\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eHooked or kinked point, nozzle opening undamaged\u003c\/td\u003e\n\u003ctd\u003eThe needle\u003c\/td\u003e\n\u003ctd\u003eHHA-2202\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShaft wobbles when rolled on the bench\u003c\/td\u003e\n\u003ctd\u003eBent needle\u003c\/td\u003e\n\u003ctd\u003eHHA-2202\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCracked nozzle tip, paint seeping forward at rest\u003c\/td\u003e\n\u003ctd\u003eNozzle\u003c\/td\u003e\n\u003ctd\u003e0.5 mm nozzle HHA-2102\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFresh needle in, spray still uneven\u003c\/td\u003e\n\u003ctd\u003eNozzle hurt too\u003c\/td\u003e\n\u003ctd\u003e0.5 mm set HHA-2002\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpatter after the airbrush stood with paint in it\u003c\/td\u003e\n\u003ctd\u003eDried paint on the needle\u003c\/td\u003e\n\u003ctd\u003eClean before replacing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eClean the needle first, since crusted paint mimics damage. Then sight along it: any curve in the shaft, or a point that bends off line or feels rough against a fingernail, means it can no longer close the nozzle evenly.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAir disconnected, airbrush clean.\u003c\/li\u003e\n\u003cli\u003eCaps off, nozzle unscrewed with the wrench, needle chucking nut loosened; draw the old needle out through the front.\u003c\/li\u003e\n\u003cli\u003eFeed the new one in from the front, put the nozzle and caps back, and bring the needle forward with a light touch until it meets the nozzle, never forced.\u003c\/li\u003e\n\u003cli\u003eTighten the chucking nut and run water or cleaner through before any paint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eKeep the tube: it is the right place for the next spare. Rest the airbrush on a holder whenever you set it down, since a needle left loose on the bench is the one that gets knocked.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOn a Zephyr still on its original 0.3 mm parts, HHA-2201 is the needle to order; this one only works alongside the 0.5 mm nozzle and caps.\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr alone: we make no claim that it fits any other airbrush.\u003c\/li\u003e\n\u003cli\u003eOne of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812136637,"sku":"HHA-2202","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-5mm-needle-hha-2202-2.jpg?v=1795190859"},{"product_id":"hobby-heaven-zephyr-0-3mm-nozzle-cap-hha-2301","title":"Hobby Heaven Zephyr 0.3mm Nozzle Cap (HHA-2301) – Replacement Airbrush Spare","description":"\u003cp\u003eEvery Zephyr spray pattern is shaped at the nozzle cap: the polished piece with the knurled ring at the front end that covers the nozzle. Its opening is cut for one nozzle size, and HHA-2301 is the 0.3 mm version, the size a Zephyr wears straight from the box. It usually takes the hit when an airbrush is dropped, and it is easy to lose during cleaning. When nozzle and needle have survived, replacing the cap on its own puts things right.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eOpening sized for nozzle HHA-2101 (0.3 mm)\u003c\/li\u003e\n\u003cli\u003eAlso part of set HHA-2001\u003c\/li\u003e\n\u003cli\u003eRidged ring around the rim for grip; no tool required\u003c\/li\u003e\n\u003cli\u003ePacked in a foam-filled clear tube with a white screw lid and the size printed on the side\u003c\/li\u003e\n\u003cli\u003eNeedle cap HHA-2401 threads onto its front\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003eAir rushing past the end of the nozzle is guided by this cap, and the even ring of air it forms is what breaks the paint into a fine, centred spray. Bend its rim, cross its thread or seat it crooked, and the air leaves unevenly, dragging the pattern off to one side.\u003c\/p\u003e\n\u003ch3\u003eIs it really the nozzle cap?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProblem\u003c\/th\u003e\n\u003cth\u003eReplacement\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eRim knocked out of shape, thread damaged or cap missing; other parts intact\u003c\/td\u003e\n\u003ctd\u003eThis cap, HHA-2301\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCrack or chip at the very end of the nozzle\u003c\/td\u003e\n\u003ctd\u003eNozzle HHA-2101 (0.3 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle point kinked\u003c\/td\u003e\n\u003ctd\u003eNeedle HHA-2201 (0.3 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront end hurt in several places by one fall\u003c\/td\u003e\n\u003ctd\u003eSet HHA-2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThe impact that bends a cap can travel through to the nozzle, so check that too before buying.\u003c\/p\u003e\n\u003ch3\u003eTelling wear from dirt\u003c\/h3\u003e\n\u003cp\u003eReal wear shows as a nick or flattened patch at the front rim, a thread that drags, a cap that will not sit square once tightened, or a spray that leans while needle and nozzle check out. Paint dried inside the cap mimics every one of these, and far more often, so give it a long soak in airbrush cleaner and scrub it out with a soft brush before anything else; the HHA-7201 brushes suit this job. Replace the cap only if the fault persists.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eAir off and disconnected first. The nozzle must already be seated, snug by hand and then given just a touch more with the wrench, before you fit the cap. Start it straight with your fingertips; if it binds, unscrew and try again, because forcing a crossed thread spoils the airbrush’s own thread. Finger pressure is all the cap needs.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eFitting this cap alone will not take a Zephyr to 0.5 mm. Spray size comes from a matched trio of needle, nozzle and nozzle cap, so a size change means the HHA-2002 set. The two sizes look alike, so keep a spare in its labelled tube. We have confirmed its fit on the Hobby Heaven Zephyr only; like every Zephyr part it has an HHA number, and the system keeps adding new ones.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812300477,"sku":"HHA-2301","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-3mm-nozzle-cap-hha-2301-2.jpg?v=1795190941"},{"product_id":"hobby-heaven-zephyr-0-5mm-nozzle-cap-hha-2302","title":"Hobby Heaven Zephyr 0.5mm Nozzle Cap (HHA-2302) – Replacement Airbrush Spare","description":"\u003cp\u003eOnce a Zephyr runs at 0.5 mm, thanks to the HHA-2002 set, its front end needs the larger nozzle cap, and this is that cap on its own. It is the knurled, polished piece the nozzle sits inside, with an opening matched to the 0.5 mm nozzle so the air surrounds the heavier flow evenly. Painters move to the 0.5 mm setup for primer, varnish and metallic paints. Order this one when a cap is lost, dented or will not seat, and the nozzle and needle behind it are undamaged.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSized for nozzle HHA-2102 (0.5 mm)\u003c\/li\u003e\n\u003cli\u003eOne of the four parts of conversion set HHA-2002\u003c\/li\u003e\n\u003cli\u003eRidged rim, so you can turn it with your fingers rather than a tool\u003c\/li\u003e\n\u003cli\u003ePacked in foam inside a labelled 0.5mm tube with a screw lid\u003c\/li\u003e\n\u003cli\u003eNeedle cap HHA-2402 (0.5 mm) screws onto its front\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat the cap does\u003c\/h3\u003e\n\u003cp\u003eAir leaving the Zephyr passes the nozzle tip inside this cap, and the cap’s opening decides how evenly it surrounds that tip. A 0.5 mm nozzle wants the 0.5 mm opening; a 0.3 mm cap on a 0.5 mm Zephyr will not spray properly.\u003c\/p\u003e\n\u003ch3\u003eIs it really the nozzle cap?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront edge bent, threads rough, or the cap has gone missing\u003c\/td\u003e\n\u003ctd\u003eThis 0.5 mm cap, HHA-2302\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChip or split where the nozzle narrows to its point\u003c\/td\u003e\n\u003ctd\u003e0.5 mm nozzle, HHA-2102\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle point curled over\u003c\/td\u003e\n\u003ctd\u003e0.5 mm needle, HHA-2202\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMore than one part damaged in a drop\u003c\/td\u003e\n\u003ctd\u003eSet HHA-2002 (the whole 0.5 mm front end)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eInspect the nozzle under magnification after any fall: damage to the cap often travels inward.\u003c\/p\u003e\n\u003ch3\u003eWhen to change it\u003c\/h3\u003e\n\u003cp\u003eLook for a burr or flattened patch on the rim, a thread that binds or lets the cap sit askew, and a pattern that leans one way despite a healthy nozzle and needle. Before blaming the part, rule out dried paint by soaking the cap in cleaner and scrubbing inside with a soft brush, such as one from the HHA-7201 set. If the fault remains, swap it.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eWith the air line disconnected and the nozzle already seated firmly, offer the cap up square and turn it by hand. Stop and restart if the thread catches rather than forcing it, since cross-threading harms the body. Finger-tight holds it; leave the wrench for the nozzle.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eTo return to 0.3 mm, fit the 0.3 mm cap HHA-2301 with its matching nozzle and needle, or the complete HHA-2001 set. Both sizes look much the same at a glance, so store whichever cap is off the airbrush in its labelled tube. Its fit is confirmed on the Hobby Heaven Zephyr alone; on any other airbrush, assume it will not fit. Each Zephyr part carries its own HHA number, and new parts keep joining the system under the same numbering.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812431549,"sku":"HHA-2302","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-5mm-nozzle-cap-hha-2302-2.jpg?v=1795190948"},{"product_id":"hobby-heaven-zephyr-0-3mm-needle-cap-hha-2401","title":"Hobby Heaven Zephyr 0.3mm Needle Cap (HHA-2401) – Front Crown Needle Guard","description":"\u003cp\u003eRight at the tip of a Zephyr, threaded over the nozzle cap, sits the needle cap. It is there to keep bumps away from the needle point, which bends more easily than anything else on the airbrush and spoils the spray the moment it does. HHA-2401 suits the 0.3 mm setup every Zephyr is delivered with. Since it is the piece you unscrew for close detail and then put down somewhere, it is also the one that goes missing; a spare stops the needle running unguarded.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCovers the point of the HHA-2201 needle (0.3 mm)\u003c\/li\u003e\n\u003cli\u003eOpen at the front, so spray leaves unobstructed and the needle point stays in view\u003c\/li\u003e\n\u003cli\u003eRidged rim to turn it with your fingers\u003c\/li\u003e\n\u003cli\u003eThreads onto nozzle cap HHA-2301\u003c\/li\u003e\n\u003cli\u003eComes in a clear, foam-packed tube marked 0.3mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eDetail work without the cap\u003c\/h3\u003e\n\u003cp\u003eUnscrewing the needle cap exposes the point, so you can watch it, bring the airbrush right up to the model and brush off a crust of dried paint without dismantling the front. The needle is then bare. Work with it off only for fine lines and small details, screw it back on for general coats, and refit it whenever you set the airbrush aside.\u003c\/p\u003e\n\u003ch3\u003eIs it really the needle cap?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSign\u003c\/th\u003e\n\u003cth\u003eOrder this\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle cap gone, bent at the rim or not threading\u003c\/td\u003e\n\u003ctd\u003eThis cap, HHA-2401\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNozzle cap knocked out of shape or lost\u003c\/td\u003e\n\u003ctd\u003eNozzle cap HHA-2301 (0.3 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKinked or curled needle point\u003c\/td\u003e\n\u003ctd\u003eHHA-2201 needle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTwo or more front parts damaged at once\u003c\/td\u003e\n\u003ctd\u003eSet HHA-2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eA dented needle cap has usually done its job, yet a hard knock can still reach the point behind it, so inspect the needle with a loupe or magnifier.\u003c\/p\u003e\n\u003ch3\u003eWhen it is time for a new one\u003c\/h3\u003e\n\u003cp\u003eChange it when the rim is dented or rough, the thread grates, the cap tilts once tightened, or it touches the needle point. Most of those complaints are really caked paint, though: leave the cap to soak in cleaner for a while, then clear it out with a soft HHA-7201 brush, and only then decide.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eWith the air disconnected, confirm the nozzle cap underneath is fully home, then spin the needle cap on with light finger pressure. Should the thread bite crookedly, take it off and line it up afresh. It needs no tool and no force. Whenever it is off, mind where the exposed needle point goes.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eSwapping needle caps leaves the spray size untouched, because size is decided by the needle, the nozzle and the nozzle cap working together. A Zephyr converted with HHA-2002 takes the 0.5 mm needle cap, HHA-2402. Zephyr owners only: we have not confirmed it on other airbrushes. Each part in the growing Zephyr system has its own HHA number for reordering.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812562621,"sku":"HHA-2401","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-3mm-needle-cap-hha-2401-2.jpg?v=1795190956"},{"product_id":"hobby-heaven-zephyr-0-5mm-needle-cap-hha-2402","title":"Hobby Heaven Zephyr 0.5mm Needle Cap (HHA-2402) – Front Crown Needle Guard","description":"\u003cp\u003eA Zephyr fitted with the larger 0.5 mm set (HHA-2002) carries a 0.5 mm needle cap at the very front, and this listing is that cap as a single spare. It threads onto the 0.5 mm nozzle cap and guards the needle point, the most delicate part of the airbrush, against bumps from the work surface, a stand or the model in your hand. Painters often take it off for close work and set it down, which is how it disappears; a replacement keeps the 0.5 mm needle covered.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eGuards the point of needle HHA-2202 (0.5 mm)\u003c\/li\u003e\n\u003cli\u003eOpen-ended, so the spray passes freely and you can still check the needle point\u003c\/li\u003e\n\u003cli\u003eRidged rim for turning by hand\u003c\/li\u003e\n\u003cli\u003eThreads onto the 0.5 mm nozzle cap HHA-2302\u003c\/li\u003e\n\u003cli\u003eShips in foam in a clear tube marked 0.5mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhen to take it off\u003c\/h3\u003e\n\u003cp\u003eRemoving the cap lets you see the point, get nearer the model and clear a dried bead of paint from the needle without dismantling anything; the needle is exposed while you do. Leave it fitted for general spraying, take it off only for close detail, and refit it before the airbrush goes back in its holder.\u003c\/p\u003e\n\u003ch3\u003eIs it really the needle cap?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront guard missing, bent or will not thread\u003c\/td\u003e\n\u003ctd\u003eHHA-2402, this listing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNozzle cap marked or lost\u003c\/td\u003e\n\u003ctd\u003eNozzle cap HHA-2302 (0.5 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle point curled\u003c\/td\u003e\n\u003ctd\u003eNeedle HHA-2202 (0.5 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront end damaged in more than one place\u003c\/td\u003e\n\u003ctd\u003eSet HHA-2002 (all four 0.5 mm parts)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eA dented guard usually means it did its job, but check the needle point under magnification anyway.\u003c\/p\u003e\n\u003ch3\u003eWhen to replace it\u003c\/h3\u003e\n\u003cp\u003eReplace it if the rim is bent or burred, if the thread binds, or if the cap sits crooked or touches the needle point. First rule out dried paint, which causes most of these complaints: soaking it in cleaner, then working the inside with a soft brush from the HHA-7201 set, usually puts it right.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eDisconnect the air, check that the nozzle cap below it is seated, then turn the needle cap on with your fingers. If it catches, unscrew it and line it up again; never force it. Finger-tight is enough. Keep the uncovered front away from surfaces while it is off.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eChanging needle caps will not change the spray width; that is set by the needle together with the nozzle and its cap. Returning to 0.3 mm means switching to needle cap HHA-2401. Both sizes look alike, so keep each in its marked tube. We vouch for its fit on the Zephyr and on nothing else, and it is numbered within the Zephyr system, which is still expanding.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812660925,"sku":"HHA-2402","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-5mm-needle-cap-hha-2402-2.jpg?v=1795190964"},{"product_id":"hobby-heaven-zephyr-trigger-main-lever-hha-3101","title":"Hobby Heaven Zephyr Trigger Main Lever (HHA-3101) – Replacement Airbrush Spare","description":"\u003cp\u003eOn the Hobby Heaven Zephyr, everything you spray starts at this lever. Press it and the lower pin opens the air valve; rock it back and it pulls the needle drive rearwards, so the needle leaves its seat and paint joins the airflow. A small hinge between stem and pin lets the button tilt while the pin still holds the valve open. Nothing but the needle keeps the trigger in its slot, so with the needle taken out for cleaning it simply falls free, and a lost trigger is the commonest reason to order this part.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA complete lever: grooved button, stem, hinge and pin, nothing to assemble\u003c\/li\u003e\n\u003cli\u003eSame part whether your Zephyr is set up for 0.3 mm or carries the HHA-2002 0.5 mm set\u003c\/li\u003e\n\u003cli\u003eBuilt for the Hobby Heaven Zephyr; fit on other airbrushes is not confirmed\u003c\/li\u003e\n\u003cli\u003eBlister label: HHA-3101 and barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs the trigger really the problem?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eWhere to look\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eLever gone, or it dropped out during cleaning\u003c\/td\u003e\n\u003ctd\u003eThis trigger\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStem bent, hinge loose, pin bent or burred\u003c\/td\u003e\n\u003ctd\u003eThis trigger\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLever stays down or returns slowly\u003c\/td\u003e\n\u003ctd\u003eClean away dried paint first; if no better, the air valve (HHA-3401)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir hisses with the lever at rest\u003c\/td\u003e\n\u003ctd\u003eAir valve (HHA-3401) failing to close\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLever travels back, needle stays put\u003c\/td\u003e\n\u003ctd\u003eLoose chucking nut (HHA-3202)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLever floppy, no return\u003c\/td\u003e\n\u003ctd\u003eGuide (HHA-3201) went back crooked; refit it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eTime for a new one when the stem leans instead of standing upright, the hinge rocks sideways, the pin is bent or worn so air arrives at a different point on every press, or the button has worked loose. Stickiness alone almost never means wear.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eKeep the parts diagram from the quick start guide to hand and disconnect the air. Take off the handle, slacken the chucking nut, unscrew the nozzle and pull the needle forward out of the front. Remove spring case and knob, then the spring and guide. Set the new trigger in pin-first, resting on the valve. Reassemble in reverse order: guide plate behind the trigger, spring, spring case and knob, needle from the front, nozzle and caps. Ease the needle forward until it meets the nozzle, finger-tighten the chucking nut and test air and needle travel without paint.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eMost triggers go missing during cleaning: with the needle out, keep the airbrush upright or park the trigger in a dish. Wipe paint off the body before it can creep into the trigger slot, and keep the air valve away from solvent soaks and ultrasonic cleaners. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812791997,"sku":"HHA-3101","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-trigger-main-lever-hha-3101-2.jpg?v=1795191002"},{"product_id":"hobby-heaven-zephyr-needle-chucking-guide-hha-3201","title":"Hobby Heaven Zephyr Needle Chucking Guide (HHA-3201) – Replacement Airbrush Spare","description":"\u003cp\u003eBehind the trigger of the Hobby Heaven Zephyr sits the part that really moves the needle. The needle passes along its centre, and the chucking nut clamps it at the split, threaded rear end. When you rock the trigger backwards, it bears on the curved front plate, so guide and needle slide rearwards together against the return spring; release it and the spring pushes both forward until the needle closes the nozzle and paint stops. The rear control knob limits the guide's travel, and the angle of its plate shapes how the pull feels.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCurved front plate with centre bush, polished body, slotted threaded tail\u003c\/li\u003e\n\u003cli\u003eServes the 0.3 mm setup and a Zephyr rebuilt for 0.5 mm alike\u003c\/li\u003e\n\u003cli\u003eMade solely for the Hobby Heaven Zephyr; no other model confirmed\u003c\/li\u003e\n\u003cli\u003ePacked in a blister marked HHA-3201 with barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs the guide to blame?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you see\u003c\/th\u003e\n\u003cth\u003eLikely cause\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger comes back, needle does not\u003c\/td\u003e\n\u003ctd\u003eSnug the chucking nut (HHA-3202) first; slipping with a firm nut means a worn tail, so this part\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo return or untidy shut-off right after a rebuild\u003c\/td\u003e\n\u003ctd\u003ePlate seated at a wrong angle; reseat it before ordering\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSlack in the trigger\u003c\/td\u003e\n\u003ctd\u003eSpring case (HHA-3203) not fully screwed in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLever sticks or returns slowly\u003c\/td\u003e\n\u003ctd\u003ePaint residue, else the air valve (HHA-3401); rarely the guide\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger missing or bent\u003c\/td\u003e\n\u003ctd\u003eTrigger (HHA-3101)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBody bent, plate cracked, slots splayed, thread damaged\u003c\/td\u003e\n\u003ctd\u003eThis part\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eReplace it when the needle shifts in the guide although the nut is tight, the tail slots have opened up or one side is bent, the nut will not run on smoothly over a flattened thread, the body catches as it slides, or the plate is cracked or distorted. One that was only refitted back to front is fine; reseat it.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eAir off, then follow the parts diagram in the quick start guide. Remove the handle, ease off the nut, unscrew the nozzle and slide the needle forward and out. Take out spring case and knob, then draw out spring and old guide. Fit the new guide behind the trigger, plate angled so the pull feels even: this single step decides how the trigger feels. Refit spring and spring case by hand, the needle is threaded in from the front, then nozzle and caps; push the needle home lightly until it meets the nozzle and finger-tighten the nut.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eOnly fingers on the chucking nut: pliers squeeze the slotted tail out of round and it loses its grip. Nut, spring and spring case are sold separately. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436812890301,"sku":"HHA-3201","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-needle-chucking-guide-hha-3201-2.jpg?v=1795191010"},{"product_id":"hobby-heaven-zephyr-needle-chucking-nut-hha-3202","title":"Hobby Heaven Zephyr Needle Chucking Nut (HHA-3202) – Replacement Airbrush Spare","description":"\u003cp\u003eLook through the cutaway handle of the Hobby Heaven Zephyr and the small knurled part at the back is this nut. It screws onto the needle chucking guide's split tail; tightening it squeezes that end around the needle, so needle and guide move as one with every pull of the trigger. When it slackens, the trigger still travels but the needle stays where it is and nothing sprays. Because it comes off at every needle clean, it ranks among the easiest parts to lose.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDiamond-knurled grip, tightened and loosened with fingers\u003c\/li\u003e\n\u003cli\u003eInternal thread matching the guide (HHA-3201)\u003c\/li\u003e\n\u003cli\u003eSmall rear opening for the needle tail: the needle can be adjusted while the nut is merely slackened\u003c\/li\u003e\n\u003cli\u003eShipped in a clear vial with a screw cap and foam insert, inside a blister marked HHA-3202\u003c\/li\u003e\n\u003cli\u003eOne nut for both the 0.3 mm and 0.5 mm builds; made for the Zephyr\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNut, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSign\u003c\/th\u003e\n\u003cth\u003eWhat to check\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eNut lost\u003c\/td\u003e\n\u003ctd\u003eThis part\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger moves, needle stays still\u003c\/td\u003e\n\u003ctd\u003eNut slack: snug it up firmly with fingers, usually no part needed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpins without biting or will not start square\u003c\/td\u003e\n\u003ctd\u003eDamaged thread: this part, and look over the guide's thread too\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNut tight and undamaged, needle still slips\u003c\/td\u003e\n\u003ctd\u003eWorn guide tail: guide (HHA-3201)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint flows before the trigger comes back\u003c\/td\u003e\n\u003ctd\u003eNeedle clamped before it seated: slacken, let it settle into the nozzle, retighten\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger floppy, no return\u003c\/td\u003e\n\u003ctd\u003eLook at the guide (HHA-3201) or spring case (HHA-3203) instead\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eIt has gone missing, spins without ever biting, only starts at an angle, or the knurling is flattened and the nut squashed or split, which pliers usually cause. One that has simply loosened only needs tightening.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eAir off, handle unscrewed. Check that the needle is fitted and resting lightly in the nozzle, not forced. Start the nut square on the guide's threaded tail with your fingers, snug it up firmly, pull the trigger back to watch the needle follow, then screw the handle back on.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eHang on to the vial: it is the natural home for the nut while the handle is off. Seat the needle first and tighten afterwards, never the other way round. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813054141,"sku":"HHA-3202","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-needle-chucking-nut-hha-3202-2.jpg?v=1795191017"},{"product_id":"hobby-heaven-zephyr-spring-case-hha-3203","title":"Hobby Heaven Zephyr Spring Case (HHA-3203) – Replacement Airbrush Spare","description":"\u003cp\u003eSeated in the tail of the Hobby Heaven Zephyr body, this threaded sleeve keeps the needle return spring pressed onto the needle chucking guide. Draw the trigger rearwards and the guide squeezes the spring inside the case; let go and the compressed spring drives guide, needle and trigger forward until the needle shuts the nozzle and the paint stops. The sleeve is hollow, so the guide's tail and the needle pass straight through on their way to the chucking nut; the rear control knob sits behind. It goes in until it seats and offers no tension adjustment.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eExternal thread and fluted grip, turned by hand\u003c\/li\u003e\n\u003cli\u003eHollow bore for spring, guide tail and needle\u003c\/li\u003e\n\u003cli\u003eThe spring is not in the pack: move the one from your old case across\u003c\/li\u003e\n\u003cli\u003eFits a 0.3 mm Zephyr and a 0.5 mm conversion equally; built for the Zephyr\u003c\/li\u003e\n\u003cli\u003eHobby Heaven blister, label HHA-3203 with barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs the spring case at fault?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat happens\u003c\/th\u003e\n\u003cth\u003eCheck this\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eSlack in the trigger\u003c\/td\u003e\n\u003ctd\u003eCase not fully in: turn it by hand until it bottoms out\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCase missing\u003c\/td\u003e\n\u003ctd\u003eThis part, plus the spring that lived inside it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStarts crooked, cross-threads or turns stiffly\u003c\/td\u003e\n\u003ctd\u003eDamaged thread: this part; inspect the body's thread as well\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBent or dented, guide catches inside\u003c\/td\u003e\n\u003ctd\u003eThis part\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle ignores the trigger\u003c\/td\u003e\n\u003ctd\u003eChucking nut (HHA-3202)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo return after a strip-down\u003c\/td\u003e\n\u003ctd\u003eGuide (HHA-3201) reseated at a wrong angle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eIts thread is burred, flattened or crossed; the case is dented or bent, typically after the airbrush landed on its tail; or the fluted grip is so marked by pliers that fingers can no longer turn it. A case that has merely backed off needs screwing in, nothing more.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eHave the quick start guide's parts diagram open and disconnect the air. Slacken the nut, take off handle and nozzle, and withdraw the needle forwards. Unscrew the old case together with the knob and keep its spring. Confirm the guide plate still sits behind the trigger, drop the spring in, start the new case square by hand and turn it home, then refit the knob. Return the needle from the front, refit nozzle and caps, rest the needle softly in the nozzle and lock it with the nut, hand-tight.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eFingers only: pliers mark the grip. Paint residue or old lube stiffens the thread, so wipe it clean and keep it dry. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813119677,"sku":"HHA-3203","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-spring-case-hha-3203-2.jpg?v=1795191025"},{"product_id":"hobby-heaven-zephyr-cutaway-handle-hha-3301","title":"Hobby Heaven Zephyr Cutaway Handle (HHA-3301) – Replacement Airbrush Handle with O-Ring","description":"\u003cp\u003eHHA-3301 is the polished tail section of the Hobby Heaven Zephyr, the tube your hand rests on behind the trigger. It threads onto the rear of the body by hand and encloses the needle drive (chucking guide, spring case and chucking nut), shielding it from knocks and overspray. A window in its side lets you check and turn the chucking nut with the handle in place. Handles seldom wear out; they are swapped after a fall dents one, a thread gets crossed or one goes astray. It is the same handle whether your Zephyr runs a 0.3 mm or a 0.5 mm nozzle.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRubber O-ring already seated where the thread meets the tube\u003c\/li\u003e\n\u003cli\u003eSide window onto the chucking nut\u003c\/li\u003e\n\u003cli\u003eOpen tail, threaded inside, that takes the rear knob, HHA-3302\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr only, whichever nozzle size it carries\u003c\/li\u003e\n\u003cli\u003eComes in a Hobby Heaven box with the HHA-3301 label; knob not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHandle, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eRemedy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDented, kinked or split after a fall\u003c\/td\u003e\n\u003ctd\u003eReplace the handle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWill not start straight or binds as it turns\u003c\/td\u003e\n\u003ctd\u003eDamaged thread: replace it, and inspect the body's thread too\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRattles or unscrews itself\u003c\/td\u003e\n\u003ctd\u003eUsually a flat or missing O-ring; a new handle arrives with one fitted\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear knob will not hold or will not go in\u003c\/td\u003e\n\u003ctd\u003eTry a new knob (HHA-3302) first; if that fails too, the handle's inner thread is at fault\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle stays put when the trigger moves\u003c\/td\u003e\n\u003ctd\u003eA loose chucking nut (HHA-3202), not this part\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger loose or slow to return\u003c\/td\u003e\n\u003ctd\u003eLook at the spring case (HHA-3203) or chucking guide (HHA-3201) instead\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA kink or dent from landing on its tail, a burred or crossed thread that no longer runs smoothly, an inner thread that can no longer grip the knob, or a handle that has gone missing. Scuffs on the polish are only cosmetic.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eDisconnect the air first. Turn the old handle off by hand; if the knob sits in its tail, take the knob out and set it aside for the new one. Check that the O-ring sits on the replacement, start it square on the body and turn it until snug, with no tools. On a full rebuild the handle is the last part to go on. Finish by screwing the knob back into the tail.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eHand pressure is all the thread needs, and forcing it can strip it. Wipe off any paint that reaches the thread while it is still wet. We can only vouch for it on the Zephyr itself: thread and length vary from one airbrush to the next, so treat it as unsuitable for other models. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813250749,"sku":"HHA-3301","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-cutaway-handle-hha-3301-2.jpg?v=1795192447"},{"product_id":"hobby-heaven-zephyr-rear-control-knob-hha-3302","title":"Hobby Heaven Zephyr Rear Control Knob (HHA-3302) – Preset Paint Flow Limiter with O-Ring","description":"\u003cp\u003eHHA-3302 is the fluted knob screwed into the very back of a Hobby Heaven Zephyr. It threads into the open end of the cutaway handle and acts as an end stop on the trigger's rearward stroke. In a dual-action design, that stroke sets how far the needle withdraws from the nozzle, so the knob caps the most paint a full pull can deliver. Wind it in for a tight maximum, handy for repeated fine lines or highlights; wind it out and the whole range returns. It limits paint only: air pressure stays wherever your regulator puts it.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTurned with the fingers, no tools needed\u003c\/li\u003e\n\u003cli\u003eRubber O-ring fitted; its light friction helps the knob keep a setting\u003c\/li\u003e\n\u003cli\u003eHollow front shaft that meets the needle drive inside the handle\u003c\/li\u003e\n\u003cli\u003eWorks at either nozzle size, 0.3 or 0.5 mm; made for the Zephyr alone\u003c\/li\u003e\n\u003cli\u003ePacked in a Hobby Heaven blister, HHA-3302 and barcode on the label\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetting a limit\u003c\/h3\u003e\n\u003cp\u003eBegin with the knob backed well out. On scrap card, draw the trigger back until the spray gives you the result you want to reproduce, hold it there and wind the knob in until it meets the trigger's travel and stops it. Release, test again and adjust a fraction either way. A lighter pull than the preset still works whenever you want one; to remove the limit, unwind the knob until it stops touching anything.\u003c\/p\u003e\n\u003ch3\u003eKnob, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat happens\u003c\/th\u003e\n\u003cth\u003eTry this\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir but little or no paint, even at full pull\u003c\/td\u003e\n\u003ctd\u003eKnob wound in too far: back it out a few turns before replacing anything\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eThe setting creeps while you work\u003c\/td\u003e\n\u003ctd\u003eO-ring worn or gone; a new knob comes with one fitted\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBent, burred, or will not start straight\u003c\/td\u003e\n\u003ctd\u003eReplace the knob; if a new one also refuses, check the handle (HHA-3301)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKnob lost\u003c\/td\u003e\n\u003ctd\u003eReplace it; until then the airbrush works, just without a preset\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger moves, needle stays still\u003c\/td\u003e\n\u003ctd\u003eThe chucking nut (HHA-3202) is loose; the knob is not involved\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA bend from a drop onto the tail, a flattened or crossed thread, a knob that drifts off its setting even with a sound O-ring, or one that has gone missing.\u003c\/p\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eDisconnect the air, unscrew any old knob from the tail of the handle, check the O-ring on the new one, start it square and give it a few turns, then set it as above. Fingers only, and no force when it reaches either stop. If you strip the airbrush down to clean it, back the knob out first or remember where it sat. Confirmed for the Hobby Heaven Zephyr and nothing else. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813414589,"sku":"HHA-3302","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-rear-control-knob-hha-3302-2.jpg?v=1795192459"},{"product_id":"hobby-heaven-zephyr-air-valve-hha-3401","title":"Hobby Heaven Zephyr Air Valve (HHA-3401) – Complete Assembled Replacement Valve","description":"\u003cp\u003eHHA-3401 is the air valve of the Hobby Heaven Zephyr, the unit beneath the trigger that your hose connects to. It is the airbrush's air switch: a spring holds a small piston shut until the trigger presses the valve pin down, air then rises through the airbrush towards the nozzle, and the moment you let go the spring shuts it off. It arrives as a single assembled unit with its O-ring, spring, piston and pin already in place, and one valve suits the Zephyr with either nozzle size, 0.3 mm or 0.5 mm.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eComplete and assembled, ready to screw in\u003c\/li\u003e\n\u003cli\u003eRubber O-ring fitted to seal the joint with the airbrush body\u003c\/li\u003e\n\u003cli\u003eKnurled collar for fitting and removing it by hand\u003c\/li\u003e\n\u003cli\u003eLower end is the Zephyr's air inlet, 1\/8\" BSP male, taking a hose directly or a quick-disconnect plug\u003c\/li\u003e\n\u003cli\u003eZephyr only; sold in a Hobby Heaven blister marked HHA-3401\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eValve, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSign\u003c\/th\u003e\n\u003cth\u003eProbable cause, then remedy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir keeps coming after you release the trigger\u003c\/td\u003e\n\u003ctd\u003eValve not sealing, often paint or solvent inside: dry it, clean it and lubricate lightly before replacing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger stays down or rises slowly\u003c\/td\u003e\n\u003ctd\u003eUsually the same sticky valve; clean first, replace if it persists\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss around the top of the valve\u003c\/td\u003e\n\u003ctd\u003eSnug it by hand and inspect its O-ring; replacements arrive with a fresh one\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss at the hose joint below\u003c\/td\u003e\n\u003ctd\u003eThe hose fitting or a quick-disconnect (HHA-5103) is leaking, not the valve; brush soapy water over the joint to find it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo air at all\u003c\/td\u003e\n\u003ctd\u003eFirst rule out the supply: compressor, regulator, hose; if air gets as far as the airbrush and stops, suspect the valve\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir arrives, paint does not\u003c\/td\u003e\n\u003ctd\u003eLook at the chucking nut (HHA-3202) or rear knob (HHA-3302)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eLeaking at rest or sticking after a proper clean and light lubrication, a bent pin, a damaged thread, or solvent damage that has not settled once the valve dried out.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eSwitch the compressor off and take the hose or coupler off the valve. Unscrew the old valve by its collar, confirm the O-ring is on the new one and run it in straight by hand until snug; no force or pliers are needed for it to seal. With no air connected, work the trigger several times to check it moves down freely and springs back, then reconnect: the air should stop the instant the trigger rises, with no hiss at the valve.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eKeep the valve out of solvent baths: thinner swells its rubber seals, the commonest reason a valve sticks. Take it out before you soak the body. A sticky valve needs only a drop of airbrush lubricant, never machine oil or penetrating spray. Its fit is confirmed on our Zephyr only. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813512893,"sku":"HHA-3401","price":3.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-air-valve-hha-3401-2.jpg?v=1795192473"},{"product_id":"hobby-heaven-zephyr-7ml-fluid-cup-hha-4101","title":"Hobby Heaven Zephyr 7ml Fluid Cup (HHA-4101) – Screw-In Gravity Cup with Vented Lid","description":"\u003cp\u003eHHA-4101 is the 7 ml (1\/4 oz) gravity cup of the Hobby Heaven Zephyr, the same size the airbrush ships with. A short threaded connector, sealed by a rubber O-ring, screws down into the airbrush, and paint feeds to the nozzle under its own weight, so very little is left behind. The screw-on lid prevents spills at steep angles and keeps dust out, while a small vent hole lets air in as the level drops. Buy it to replace a dented cup or lost lid, or as a second cup so one colour waits mixed while you clean the other.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHolds 7 ml, enough for miniatures and model panels without unbalancing the airbrush\u003c\/li\u003e\n\u003cli\u003eScrew-on lid with a knurled edge and a vent hole\u003c\/li\u003e\n\u003cli\u003eRubber O-ring fitted above the connector thread\u003c\/li\u003e\n\u003cli\u003ePolished inside, so it rinses quickly between colours\u003c\/li\u003e\n\u003cli\u003eWindow carton with a foam insert, labelled HHA-4101\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCup, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProblem\u003c\/th\u003e\n\u003cth\u003eFix\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint seeps out round the base\u003c\/td\u003e\n\u003ctd\u003eSnug the cup by hand and inspect the O-ring; every new cup has one fitted\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCup will not start straight or feels gritty\u003c\/td\u003e\n\u003ctd\u003eDried paint in a thread: clean both; replace only if the cup's own thread is damaged\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlow dwindles as the level drops with the lid fitted\u003c\/td\u003e\n\u003ctd\u003eVent hole blocked: clear it with a fine cleaning needle (HHA-7202)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint escapes from the vent\u003c\/td\u003e\n\u003ctd\u003eCup overfilled or tilted steeply: two thirds full is plenty\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBubbles in the paint while spraying\u003c\/td\u003e\n\u003ctd\u003eNot the cup: nozzle or nozzle cap not seated (HHA-2101\/2102, HHA-2301\/2302)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDented cup, lost lid or damaged lid thread\u003c\/td\u003e\n\u003ctd\u003eReplace the cup; the lid comes with it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eRinse out the old cup, then unscrew it by hand. Check the O-ring sits just above the connector thread of the replacement, start it straight and turn until it stops; it needs no force to seal. Test it with some water or cleaner and watch the base for weeping before adding paint. Clean straight after each session, outlet and vent included, with a soft brush (HHA-7201) or cotton bud rather than anything sharp that could scratch the polish. The cup comes off on its own, so the airbrush never needs soaking for it.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThis cup has only been tested on the Hobby Heaven Zephyr. Many gravity-feed airbrushes take a screw-in cup on a small connector, so it may suit yours, but threads vary between makes and no fit is guaranteed: compare it with your current cup's connector first. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813643965,"sku":"HHA-4101","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-7ml-fluid-cup-hha-4101-2.jpg?v=1795192482"},{"product_id":"hobby-heaven-airbrush-quick-disconnect-coupler-female-hha-5101","title":"Hobby Heaven Airbrush Quick Disconnect Coupler, Female (HHA-5101) – 1\/8\" BSP","description":"\u003cp\u003eHHA-5101 is the hose half of a quick-disconnect air connection, a socket that stays screwed to the end of your airbrush hose. A small plug fitted to the airbrush (HHA-5102) pushes into it and locks with a click; pull the knurled sleeve back to free the airbrush. While the socket is empty, a valve inside it stays closed, so the hose stays silent and the compressor can keep running as you change airbrushes or take one to the sink. It has no air flow valve, and it is exactly the coupler packed with the Hobby Heaven Zephyr.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e1\/8\" BSP male thread at its base, for a hose with a 1\/8\" BSP female end\u003c\/li\u003e\n\u003cli\u003eAccepts standard 5 mm plugs made for airbrush quick-disconnects\u003c\/li\u003e\n\u003cli\u003eAir cuts off automatically the moment the plug is withdrawn\u003c\/li\u003e\n\u003cli\u003eSpring-loaded knurled release sleeve, plus a hex for holding it with a spanner\u003c\/li\u003e\n\u003cli\u003eOne coupler in a Hobby Heaven blister labelled HHA-5101; plug not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCoupler, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYou notice\u003c\/th\u003e\n\u003cth\u003eCause and cure\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eA hiss at the hose joint\u003c\/td\u003e\n\u003ctd\u003eThread unsealed: add a few turns of thread-sealing tape and refit by hand\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eA hiss at the click joint although the plug is locked\u003c\/td\u003e\n\u003ctd\u003eThe internal seal has worn out: fit a new coupler\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo air although the plug is in\u003c\/td\u003e\n\u003ctd\u003ePlug short of the click, so the shut-off is still closed: press it fully home\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePlug won't lock, or drops out\u003c\/td\u003e\n\u003ctd\u003eGrit in the sleeve: clean it, and replace the coupler if that fails\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIt will not start in your hose\u003c\/td\u003e\n\u003ctd\u003eA different fitting: Badger, Paasche or Aztek hoses take a brand adapter first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA hiss at the click joint even with the plug pushed fully home, a sleeve that sticks or no longer holds the plug, air escaping from the hose with nothing connected, or a thread bent or crushed by a drop.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eCompressor off, hose bled. Unscrew the hose at the airbrush, wind thread-sealing tape onto the coupler's thread, short of the end, and turn the coupler in by hand until it stops; the hex is only for holding a stubborn fitting. Fit a plug to the airbrush, restore the air, click it in and dab soapy water on every joint: bubbles give a leak away.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThe arithmetic is one coupler for each hose and a plug for each airbrush. The coupler regulates nothing: open with a plug fitted, shut without; for air control at your hand, see the valved set HHA-5104. Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex, Master and plenty of other hobby brands build to this 1\/8\" BSP thread, as does the Zephyr, and our hoses HHA-5201 and HHA-5202 and moisture trap HHA-5301 accept it directly. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813775037,"sku":"HHA-5101","price":3.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-quick-disconnect-coupler-female-hha-51-2.jpg?v=1795199948"},{"product_id":"hobby-heaven-airbrush-quick-disconnect-plug-male-hha-5102","title":"Hobby Heaven Airbrush Quick Disconnect Plug, Male (HHA-5102) – 1\/8\" BSP, 5mm Nipple","description":"\u003cp\u003eHHA-5102 is the airbrush half of a quick-disconnect connection: a small plug that is screwed onto the air inlet and then left in place. Its smooth 5 mm nipple slides into a coupler on the hose (HHA-5101) and is held there until the coupler's sleeve is drawn back. The plug has no valve of its own, because the automatic shut-off lives in the coupler; that keeps it small and inexpensive, so most painters leave one on each airbrush they own and keep a single coupler on the hose. It is the same plug that comes in the box with the Hobby Heaven Zephyr.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFemale 1\/8\" BSP thread, to suit an airbrush whose inlet is 1\/8\" BSP\u003c\/li\u003e\n\u003cli\u003eStandard 5 mm nipple for airbrush quick-disconnect couplers\u003c\/li\u003e\n\u003cli\u003eKnurled collar, so it goes on and comes off by hand\u003c\/li\u003e\n\u003cli\u003eNo internal valve: the coupler does the shutting off\u003c\/li\u003e\n\u003cli\u003eSingle plug, Hobby Heaven blister, HHA-5102 on the label; coupler sold separately\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePlug, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eWhat to check\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eHissing at the airbrush joint\u003c\/td\u003e\n\u003ctd\u003eInlet thread unsealed: unscrew, wind a little thread-sealing tape onto the airbrush's inlet and refit by hand\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHissing where it clicks in\u003c\/td\u003e\n\u003ctd\u003ePush the plug fully home; if a clean, undamaged nipple still hisses, suspect the coupler's seal (HHA-5101)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWill not click into a coupler you already own\u003c\/td\u003e\n\u003ctd\u003eThat coupler may not be a 5 mm system; pair the plug with our coupler instead\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWill not start on the airbrush\u003c\/td\u003e\n\u003ctd\u003eThe inlet is a different fitting: Badger, Paasche and Aztek airbrushes each want their own brand adapter first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNipple dented, scored or bent\u003c\/td\u003e\n\u003ctd\u003eReplace the plug, since a damaged nipple cannot seal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA nipple nicked, scored or bent after a drop, a thread that has crossed or no longer pulls up snug, or a plug that keeps leaking at a coupler which seals perfectly with another plug.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eWith the air off, unscrew the hose or the old plug from the airbrush. Tape the airbrush's inlet thread, since the plug's own thread is on the inside, and turn the plug on by hand until it seats; no tools are needed. Wipe the nipple before every connection, because grit carried into the coupler wears its seal.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eCounting is simple: a plug for every airbrush, a coupler for every hose, so a single compressor running three airbrushes calls for three plugs but just one coupler. Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex, Master and the Zephyr all use a 1\/8\" BSP male inlet, which is what this plug is made for, and it clicks into our plain coupler HHA-5101 as well as the valved set HHA-5104. Want both halves at once? The pair is sold as HHA-5103. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813906109,"sku":"HHA-5102","price":2.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-quick-disconnect-plug-male-hha-5102-2.jpg?v=1795199957"},{"product_id":"hobby-heaven-airbrush-quick-disconnect-set-hha-5103","title":"Hobby Heaven Airbrush Quick Disconnect Set (HHA-5103) – 1\/8\" BSP Coupler + Plug","description":"\u003cp\u003eHHA-5103 is a matched pair for a click-on air connection: a coupler (HHA-5101) that screws into the airbrush end of the hose and a plug (HHA-5102) that screws onto the air inlet of the airbrush. With both fitted, the airbrush clicks onto the hose and comes off again with a pull of the knurled sleeve, without working any threads or switching the compressor off, because the coupler closes itself whenever the plug is out. It is the same pair that ships with the Hobby Heaven Zephyr, so it suits a second workstation, a replacement for a lost pair, or a first quick-release setup on another airbrush.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCoupler: 1\/8\" BSP male thread, for the hose end\u003c\/li\u003e\n\u003cli\u003ePlug: female 1\/8\" BSP thread and a 5 mm nipple, for the airbrush\u003c\/li\u003e\n\u003cli\u003eAutomatic air shut-off inside the coupler; no flow valve\u003c\/li\u003e\n\u003cli\u003eChange airbrushes, or walk one over to the sink, in seconds\u003c\/li\u003e\n\u003cli\u003eBoth halves share one Hobby Heaven blister, labelled HHA-5103\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMale and female, explained\u003c\/h3\u003e\n\u003cp\u003eThe names refer to the click joint rather than the threads, so each half carries the opposite thread to the one its name suggests. The \"female\" coupler is the socket the plug enters, yet its thread is on the outside to suit the hose. The \"male\" plug carries the nipple, yet its thread is inside to suit the airbrush inlet.\u003c\/p\u003e\n\u003ch3\u003eLeak at the set, or elsewhere?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSign\u003c\/th\u003e\n\u003cth\u003eCause, then cure\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss at either threaded joint\u003c\/td\u003e\n\u003ctd\u003eWrap thread-sealing tape round the male thread (the coupler's, or the airbrush inlet) and screw it back by hand\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss at the click joint, plug home\u003c\/td\u003e\n\u003ctd\u003eWorn seal inside the coupler: replace it, HHA-5101\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo air with the airbrush connected\u003c\/td\u003e\n\u003ctd\u003ePlug not fully locked, so the coupler is still closed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eA half will not screw on\u003c\/td\u003e\n\u003ctd\u003eYour airbrush or hose uses another fitting; on a Badger, Paasche or Aztek, fit a brand adapter to convert to 1\/8\" BSP first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eAir off and hose bled. Wrap the coupler's thread and turn it into the hose; wrap the airbrush inlet and turn the plug onto it. Hand pressure is enough for both. Restore the air, press the plug in until you hear the click, then brush soapy water across the joints; any joint that bubbles needs another look.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThe coupler and plug are also sold singly (HHA-5101, HHA-5102), so a plug for each extra airbrush can be added later. To trim the air at your hand as well, choose the set with an air flow valve, HHA-5104. The 1\/8\" BSP thread is the usual air fitting across hobby airbrushes and hoses: Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex and Master use it, and so does the Zephyr. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814037181,"sku":"HHA-5103","price":4.59,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-quick-disconnect-set-hha-5103-2.jpg?v=1795199966"},{"product_id":"hobby-heaven-airbrush-quick-disconnect-set-with-air-flow-valve-hha-5104","title":"Hobby Heaven Airbrush Quick Disconnect Set with Air Flow Valve (HHA-5104) – 1\/8\" BSP","description":"\u003cp\u003eHHA-5104 is a quick-disconnect set with a second job built in. The plug lives on the airbrush and the coupler on the hose; they click together and part like any quick-disconnect, and the coupler shuts the air off once the plug is out. On the coupler sits a small knurled knob: an air flow valve, the kind often called a MAC valve, which turns the air down at your hand instead of at the compressor. Put the regulator at the session's top pressure, trim down for fine lines, stippling or thin coats, and open fully to flush cleaner.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCoupler with air flow valve: male 1\/8\" BSP thread, lives on the hose\u003c\/li\u003e\n\u003cli\u003ePlug: 5 mm nipple and female 1\/8\" BSP thread, lives on the airbrush\u003c\/li\u003e\n\u003cli\u003eKnob trims the air from fully open down to fully shut\u003c\/li\u003e\n\u003cli\u003eSpring-loaded sleeve releases the plug; air shuts off while it is out\u003c\/li\u003e\n\u003cli\u003eBoth parts packed in a Hobby Heaven blister, HHA-5104 on the label\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat the valve can and cannot do\u003c\/h3\u003e\n\u003cp\u003eAll it can do is reduce the air. The knob restricts the flow reaching the airbrush, which softens the spray, but it cannot add pressure beyond what the regulator delivers, and it has no gauge. Turned fully in, it stops the air altogether. The regulator gauge reads the pressure before the valve, so judge a trimmed setting by spraying a test card. Painters who rarely touch their pressure mid-session may prefer the cheaper plain set, HHA-5103, for the quick-release alone.\u003c\/p\u003e\n\u003ch3\u003eValve set, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProblem\u003c\/th\u003e\n\u003cth\u003eFix\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo air reaching the airbrush\u003c\/td\u003e\n\u003ctd\u003eKnob wound fully in: open it, then make sure the plug has clicked home\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeak spray although the regulator is up\u003c\/td\u003e\n\u003ctd\u003eValve half shut: open it fully and spray again first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss at a thread\u003c\/td\u003e\n\u003ctd\u003eUnsealed joint: thread-sealing tape on the male thread, then refit by hand\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss round the knob at every setting\u003c\/td\u003e\n\u003ctd\u003eValve seal worn: replace the set\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOne half refuses to thread on\u003c\/td\u003e\n\u003ctd\u003eWrong thread on the airbrush or hose; Badger, Paasche or Aztek gear needs an adapter first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eCompressor off, hose bled. Tape the coupler's thread and run it into the hose by hand; tape the airbrush inlet and fit the plug the same way. Open the knob, restore the air, click the plug in and test each joint with a dab of soapy water, then set the regulator and fine-tune with the knob.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThis set is not part of the Zephyr box, which comes with the plain pair. If you run several airbrushes, add an HHA-5102 plug for each one. Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex, Master and the Zephyr share the 1\/8\" BSP fitting this set is made for. Fingers only on the knob; never force it. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814135485,"sku":"HHA-5104","price":4.89,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-quick-disconnect-set-with-air-flow-val-2.jpg?v=1795199975"},{"product_id":"hobby-heaven-braided-airbrush-hose-1-8m-hha-5201","title":"Hobby Heaven Braided Airbrush Hose 1.8m (HHA-5201) – 1\/8\" BSP Both Ends","description":"\u003cp\u003eHHA-5201 is a 1.8 m air hose for linking an airbrush to its compressor. A knurled nut threaded 1\/8\" BSP female sits on each end, the size most hobby airbrushes and compressor regulators use for their air connections, and both nuts are done up with the fingers alone. A black braided sleeve covers the full length. That length suits a compressor standing on the desk or on a shelf close behind it, and it matches the hose packed with many compressor kits, which makes this a straight swap when an old one starts leaking or goes missing.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e1.8 m long, about 6 ft\u003c\/li\u003e\n\u003cli\u003eIdentical nut at both ends, 1\/8\" BSP female, so it goes on either way round\u003c\/li\u003e\n\u003cli\u003eBlack braided outer cover from nut to nut\u003c\/li\u003e\n\u003cli\u003eConnects directly to the Hobby Heaven Zephyr and other airbrushes with a 1\/8\" BSP male inlet\u003c\/li\u003e\n\u003cli\u003ePacked in a Hobby Heaven bag labelled HHA-5201 with its barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it connects to\u003c\/h3\u003e\n\u003cp\u003eAirbrushes from Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex or Master fit straight on, as the Zephyr does; for Badger, Paasche or Aztek, add that brand's adapter. Bigger compressors often have a 1\/4\" BSP outlet, which calls for a reducer such as the one in HHA-5401, and US-made machines may use 1\/4\" NPT, a different thread entirely. For click-on connections, fit a quick-disconnect coupler (HHA-5103 or HHA-5104) to the hose. For more reach, the 3 m hose is HHA-5202.\u003c\/p\u003e\n\u003ch3\u003eHose, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eLikely cause and remedy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eHissing at one end\u003c\/td\u003e\n\u003ctd\u003eThe joint, not the hose: reseat the nut; if that fails, tape the male thread\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNut refuses to start, or tightens after a single turn\u003c\/td\u003e\n\u003ctd\u003eA mismatched thread on the far side: stop and use an adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater spitting at the nozzle\u003c\/td\u003e\n\u003ctd\u003eCondensation: drain the compressor's trap, or add an inline trap (HHA-5301)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir escaping along the hose itself\u003c\/td\u003e\n\u003ctd\u003eA split, usually after crushing or a hard kink: replace the hose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eLeaks along the length rather than at a nut, a cracked nut or stripped thread, or a section that has been cut, crushed, melted or left permanently flattened.\u003c\/p\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eWith the compressor switched off and the line empty, run one nut onto the outlet and the second onto the airbrush or coupler, fingers only; pliers can flatten the knurled grip. Brush soapy water across both joints with the air on: bubbles mark a leak. Store it in loose coils and keep thinners, hot tools and blades away from it.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eJoining two hoses takes a 1\/8\" BSP male × male joiner, which HHA-5401 includes, though one longer hose means a joint fewer. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814332093,"sku":"HHA-5201","price":4.89,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-braided-airbrush-hose-1-8m-hha-5201-2.jpg?v=1795199857"},{"product_id":"hobby-heaven-braided-airbrush-hose-3m-hha-5202","title":"Hobby Heaven Braided Airbrush Hose 3m (HHA-5202) – 1\/8\" BSP Both Ends","description":"\u003cp\u003eHHA-5202 is a 3 m braided air hose, long enough for the compressor to live on the floor, beneath the bench or next to a spray booth rather than at your elbow, which also takes its noise further from your ear and leaves room to turn a model or stand up. The two ends carry matching knurled nuts threaded 1\/8\" BSP female, so direction does not matter and both tighten by hand. It suits the Hobby Heaven Zephyr, as our photo shows, and any other airbrush or compressor with 1\/8\" BSP male connections. If the compressor sits right beside you, the shorter HHA-5201 (1.8 m) leaves less hose lying on the desk.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e3 m long, roughly 10 ft\u003c\/li\u003e\n\u003cli\u003eMatching 1\/8\" BSP female nuts, knurled for grip\u003c\/li\u003e\n\u003cli\u003eBlack braid over its whole length\u003c\/li\u003e\n\u003cli\u003ePictured on the Zephyr with our valved quick disconnect, HHA-5104, sold separately\u003c\/li\u003e\n\u003cli\u003eComes in a Hobby Heaven bag marked HHA-5202 with its barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhich hose for your setup?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYour setup\u003c\/th\u003e\n\u003cth\u003eWhat to use\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor on the desk or a shelf just behind\u003c\/td\u003e\n\u003ctd\u003e1.8 m (HHA-5201) is enough\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor on the floor, beneath the bench or by a booth\u003c\/td\u003e\n\u003ctd\u003eThis 3 m hose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eZephyr, Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex or Master airbrush\u003c\/td\u003e\n\u003ctd\u003e1\/8\" BSP inlet: connects directly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBadger, Paasche or Aztek airbrush\u003c\/td\u003e\n\u003ctd\u003eFit that brand's inlet adapter first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor outlet 1\/8\" BSP male\u003c\/td\u003e\n\u003ctd\u003eConnects directly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor outlet 1\/4\" BSP male\u003c\/td\u003e\n\u003ctd\u003eAdd a 1\/4\" female to 1\/8\" male reducer (in HHA-5401)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUS compressor with 1\/4\" NPT\u003c\/td\u003e\n\u003ctd\u003eAn NPT-to-BSP adapter: the two threads do not seal together\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhen the air misbehaves\u003c\/h3\u003e\n\u003cp\u003eHoses seldom fail. A hiss at an end is nearly always the joint: refit the nut squarely and, if it persists, tape the male thread. A nut that stops after one turn has met a different thread, so reach for an adapter rather than force. Water spitting from the nozzle is condensation from the compressor; an inline trap such as HHA-5301 catches it at the airbrush. Air leaking through the braid means a split, usually from crushing or kinking, and then the hose should go, as it should when a nut cracks or its thread strips.\u003c\/p\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eSwitch off at the compressor and bleed the line. Tighten one end on the outlet and the far end on the airbrush or a quick-disconnect coupler, by hand. Restore the air and dab soapy water on each connection to spot bubbles. Set your pressure while spraying, because any hose reads a touch lower with air flowing. Coil it loosely and keep solvents, soldering irons and knives clear of it.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eOne long hose avoids joining two short ones, and so removes a joint that could leak. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814463165,"sku":"HHA-5202","price":5.49,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-braided-airbrush-hose-3m-hha-5202-2.jpg?v=1795199865"},{"product_id":"hobby-heaven-inline-airbrush-moisture-trap-hha-5301","title":"Hobby Heaven Inline Airbrush Moisture Trap (HHA-5301) – 1\/8\" BSP, 5 Micron","description":"\u003cp\u003eHHA-5301 is a compact inline moisture trap fitted right at the airbrush: it threads onto the air inlet, the hose threads onto it, and air flows through the trap a moment before entering the airbrush. As compressed air travels down a hose it cools, and part of its water vapour turns back to liquid; when that reaches the nozzle it spits or leaves wet spots in the paint. Inside, a filter element rated at 5 microns stops water droplets and fine dirt, which gather in a clear polycarbonate bowl in plain view. Pushing the spring-loaded pin empties it with nothing unscrewed.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAirbrush side: 1\/8\" BSP female, in a polished cap\u003c\/li\u003e\n\u003cli\u003eHose side: 1\/8\" BSP male\u003c\/li\u003e\n\u003cli\u003eA 5-micron element filters the air\u003c\/li\u003e\n\u003cli\u003ePush-pin drain that empties the bowl in place\u003c\/li\u003e\n\u003cli\u003ePictured on the Zephyr; suits other 1\/8\" BSP airbrushes and hoses\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMoisture, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you see\u003c\/th\u003e\n\u003cth\u003eLikely cause and remedy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eClear water spitting out, more so in long sessions or damp weather\u003c\/td\u003e\n\u003ctd\u003eMoisture: empty this trap and any trap on the compressor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSplatter at the start of strokes, or a grainy pattern\u003c\/td\u003e\n\u003ctd\u003eUsually the paint: thin it and wipe the needle tip clean\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss at either threaded joint\u003c\/td\u003e\n\u003ctd\u003eSnug it by hand; tape the male thread if it carries on\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDrain pin hissing\u003c\/td\u003e\n\u003ctd\u003eDebris under the pin: press and release it repeatedly under air\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater still gets through\u003c\/td\u003e\n\u003ctd\u003eIt only stops water that is already liquid: empty it more often and keep a compressor-side trap as well\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eAirbrush end or compressor end?\u003c\/h3\u003e\n\u003cp\u003eA regulator trap on the compressor handles water produced in the compressor and its tank, not moisture that forms afterwards along the hose; a trap at the airbrush covers that final stretch. With quick disconnects it can stay on the airbrush (plug HHA-5102 screwed onto the trap) or on the hose (coupler HHA-5101 or HHA-5104 on the trap). Whichever you choose, keep the drain pin on the low side while you paint.\u003c\/p\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eShut off the air and take the hose off the airbrush. Turn the trap's cap onto the inlet by hand, then the hose onto the trap. With air restored, press the pin once, and dab soapy water on both connections. Empty it before and after every session. Keep thinners and airbrush cleaner away from the bowl, since solvents can craze or split polycarbonate; a bowl that is cracked or permanently cloudy, or a pin that keeps leaking, means a new trap.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eIt is not an air dryer: it cuts the risk of water landing in your paint rather than making the air fully dry. Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex and Master airbrushes take it directly; Badger, Paasche and Aztek each require their own brand's adapter. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814561469,"sku":"HHA-5301","price":4.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-inline-airbrush-moisture-trap-hha-5301-2.jpg?v=1795199873"},{"product_id":"hobby-heaven-airbrush-thread-adapter-set-7-pcs-hha-5401","title":"Hobby Heaven Airbrush Thread Adapter Set, 7 pcs (HHA-5401) – 1\/8\", 1\/4\" BSP and M5","description":"\u003cp\u003eHHA-5401 is a box of seven thread adapters for joining airbrush equipment whose connections do not match. Airbrushes and their hoses mostly use 1\/8\" BSP, plenty of compressors, regulators and tanks use the larger 1\/4\" BSP, and the fine M5 × 0.5 turns up on mini compressors and some older hoses. Three adapters are male at both ends, for joining two female parts; four are female at one end and male at the other, for stepping between sizes. Choose ends of the same size as, and opposite gender to, the parts being joined.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJoiners: three, male at both ends\u003c\/li\u003e\n\u003cli\u003eConverters: four, female at one end and male at the other\u003c\/li\u003e\n\u003cli\u003eCovers 1\/8\" BSP, 1\/4\" BSP and M5 × 0.5, all nominal sizes\u003c\/li\u003e\n\u003cli\u003eSeven pieces, boxed and labelled HHA-5401\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhich adapter for which joint?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYour joint\u003c\/th\u003e\n\u003cth\u003eAdapter\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e1\/4\" BSP male compressor or regulator outlet, 1\/8\" BSP hose\u003c\/td\u003e\n\u003ctd\u003e1\/4\" BSP F × 1\/8\" BSP M\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM5 male outlet on a mini compressor, 1\/8\" BSP hose\u003c\/td\u003e\n\u003ctd\u003eM5 F × 1\/8\" BSP M\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1\/4\" BSP male outlet, hose ending in an M5 female nut\u003c\/td\u003e\n\u003ctd\u003e1\/4\" BSP F × M5 M\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTwo 1\/8\" BSP hoses end to end\u003c\/td\u003e\n\u003ctd\u003e1\/8\" × 1\/8\" BSP joiner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1\/4\" BSP female port on a regulator or tank, 1\/8\" BSP hose\u003c\/td\u003e\n\u003ctd\u003e1\/8\" × 1\/4\" BSP joiner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1\/8\" BSP male outlet, 1\/4\" BSP female nut on the other part\u003c\/td\u003e\n\u003ctd\u003e1\/8\" BSP F × 1\/4\" BSP M\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTwo 1\/4\" BSP female parts\u003c\/td\u003e\n\u003ctd\u003e1\/4\" × 1\/4\" BSP joiner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eIdentifying a thread\u003c\/h3\u003e\n\u003cp\u003eMeasure a male thread across its crests with a calliper. Nominal outside diameters are roughly 9.7 mm for 1\/8\" BSP, 13.2 mm for 1\/4\" BSP and 5 mm for M5. To check a female thread, offer up the matching adapter end with your fingers; a clean start and two free turns mean the same thread.\u003c\/p\u003e\n\u003ch3\u003eWhat it will not do\u003c\/h3\u003e\n\u003cp\u003eNo NPT: 1\/4\" NPT, common on US compressors, may start in a 1\/4\" BSP thread but will not seal. For Badger, Paasche or Aztek inlets, use that brand's adapter. And these are plain threaded joints; for click-on connectors, see HHA-5103 and HHA-5104.\u003c\/p\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eBegin each thread with your fingers and stop if it binds. Aim for hand-tight, with at most a light extra turn from a spanner, since small threads, M5 above all, strip easily. A hissing joint gets thread-seal tape on its male thread, kept off the tip. Chain as few adapters as possible, and retire any with a damaged thread.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThe Zephyr itself takes a standard hose with no adapter; these earn their place at the compressor and around the workshop. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814659773,"sku":"HHA-5401","price":5.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-thread-adapter-set-7-pcs-hha-5401-2.jpg?v=1795199881"},{"product_id":"hobby-heaven-zephyr-nozzle-wrench-hha-7101","title":"Hobby Heaven Zephyr Nozzle Wrench (HHA-7101) – Airbrush Nozzle Removal Tool","description":"\u003cp\u003eHHA-7101 is the small flat spanner packed in every Hobby Heaven Zephyr box, here on its own. On the Zephyr the nozzle sits threaded in the front end of the body and is too tiny to turn by hand, so this wrench is what removes it for a deep clean or a swap and what refits it afterwards. One wrench handles both Zephyr nozzle sizes, 0.3 mm (HHA-2101) and 0.5 mm (HHA-2102). Most buyers want it because the original has disappeared, or to keep a second one in their cleaning kit.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eIdentical to the wrench supplied with the Zephyr\u003c\/li\u003e\n\u003cli\u003eOpen-ended head that takes either nozzle size\u003c\/li\u003e\n\u003cli\u003eThin, flat blank that reaches into the nose of the airbrush\u003c\/li\u003e\n\u003cli\u003eHole at the handle end for a hook or key ring\u003c\/li\u003e\n\u003cli\u003eOne tool per Hobby Heaven blister, marked HHA-7101 with barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eRemoving and refitting the nozzle\u003c\/h3\u003e\n\u003cp\u003eDisconnect the air and flush the airbrush. Take off the needle cap and nozzle cap, then pull the needle back so its point is clear. Seat the wrench head fully, hold it level with the body and unscrew; once the nozzle frees, finish by hand. To refit, run the nozzle in with your fingers until it stops and give the wrench just a small extra turn, because too much force splits nozzles. Check first that its rubber O-ring is on the nozzle rather than left inside the body. On the Zephyr the needle comes out and goes back through the nose with the nozzle removed, so a needle change begins with this tool as well.\u003c\/p\u003e\n\u003ch3\u003eWrench, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you see\u003c\/th\u003e\n\u003cth\u003eLikely reason and next step\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eNozzle refuses to turn\u003c\/td\u003e\n\u003ctd\u003ePaint dried in its thread: soak the nose in airbrush cleaner and try again gently; pliers crush nozzles\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWrench keeps slipping off\u003c\/td\u003e\n\u003ctd\u003eNot pushed fully home, or held at an angle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHead spread or bent\u003c\/td\u003e\n\u003ctd\u003eReplace the wrench before it chews the nozzle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCup bubbling, or a leak at the nose once refitted\u003c\/td\u003e\n\u003ctd\u003eNozzle loose or O-ring missing: look for the O-ring, then a fraction more turn\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray spits or pulls sideways once refitted\u003c\/td\u003e\n\u003ctd\u003ePerhaps a split nozzle tip: fit a new nozzle (HHA-2101 or HHA-2102)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA spread, twisted or burred head, or a wrench that has gone astray. A worn wrench costs less than the nozzle it can damage.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eStore it with the airbrush, not in a general toolbox, so it is to hand whenever the nozzle has to come out. It is made for the Zephyr; it may well suit nozzles on other airbrushes, but none has been tried by us, so treat any other fit as untested. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814758077,"sku":"HHA-7101","price":2.49,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-nozzle-wrench-hha-7101-2.jpg?v=1795197610"},{"product_id":"hobby-heaven-airbrush-cleaning-brush-set-5-pcs-hha-7201","title":"Hobby Heaven Airbrush Cleaning Brush Set, 5 pcs (HHA-7201)","description":"\u003cp\u003eHHA-7201 is a set of five spiral brushes for the places a rinse leaves dirty. Paint clings wherever it flows slowly: the channel leading from the cup to the nozzle, the cup floor, the insides of caps and fittings. Every brush carries bristles wound onto a twisted wire stem, the heads step up in five sizes, and a single key ring holds the set together. The set suits airbrush cleaning in general rather than one model; on the Hobby Heaven Zephyr it reaches the paint channel, the 7 ml cup and both caps.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFive brushes, five head sizes\u003c\/li\u003e\n\u003cli\u003eBristles wound onto twisted wire stems\u003c\/li\u003e\n\u003cli\u003eOne key ring keeps the smallest from going missing\u003c\/li\u003e\n\u003cli\u003ePaint channel, cup, caps and fittings\u003c\/li\u003e\n\u003cli\u003eHobby Heaven bag labelled HHA-7201, with barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePicking a size\u003c\/h3\u003e\n\u003cp\u003eUse the largest head that slides in without force, as it scrubs more of the wall per stroke. The slimmest suit the paint channel and small fittings, the mid sizes the caps and the cup-to-body joint, the stoutest the cup interior and outlet.\u003c\/p\u003e\n\u003ch3\u003eHow to use them\u003c\/h3\u003e\n\u003cp\u003eRun cleaner through until the spray is clear, then withdraw the needle so no brush can bend its point. Dip a brush in cleaner, guide it into the cup outlet and twist it along the channel, in and out, until it emerges clean. Treat the cup and caps the same way, flush again to carry off whatever came loose, and put the needle back. The nozzle is the exception: remove it first (the Zephyr's wrench is HHA-7101) and use just the slimmest brush, from the back where the opening is wide. Stop when you feel resistance and never force bristles out through the tip; a soak is gentler on it.\u003c\/p\u003e\n\u003ch3\u003eDirt, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSymptom\u003c\/th\u003e\n\u003cth\u003eProbable cause\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir but no paint\u003c\/td\u003e\n\u003ctd\u003eDried paint inside: soak, then scrub the channel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpatter on the first pass after a clean\u003c\/td\u003e\n\u003ctd\u003eMoisture still inside the airbrush or line: blow air through and empty the moisture trap\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCup bubbling\u003c\/td\u003e\n\u003ctd\u003eNozzle or cap not snug; scrubbing changes nothing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray to one side or split in two\u003c\/td\u003e\n\u003ctd\u003eBent needle point or damaged nozzle, which a brush cannot mend\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrush will not enter\u003c\/td\u003e\n\u003ctd\u003eHead too large for the hole: go one size down\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCare and replacing\u003c\/h3\u003e\n\u003cp\u003eRinse each brush before paint sets on it and hang it back on the ring. A bent stem can be straightened by hand. On polished surfaces keep them wet with cleaner, since a dry wire stem may scuff them. Once the bristles are flattened or caked with paint that no longer washes out, replace the set.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eBrushes scrub; for a hard plug of paint or a blocked lid vent, the cleaning needle set (HHA-7202) does the poking. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814856381,"sku":"HHA-7201","price":2.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-cleaning-brush-set-5-pcs-hha-7201-2.jpg?v=1795197618"},{"product_id":"hobby-heaven-airbrush-cleaning-needle-set-5-pcs-hha-7202","title":"Hobby Heaven Airbrush Cleaning Needle Set, 5 pcs (HHA-7202)","description":"\u003cp\u003eHHA-7202 is a set of five cleaning needles, each a length of fine twisted wire in its own thickness, all hanging from one key ring. They go where a brush is too soft or too bulky: turned inside a hole, the spiral surface catches dried paint and pulls it out. Use them on a hardened plug in the paint channel, the vent of a cup lid, the tiny holes in caps and the bores of fittings. They are general-purpose probes, not built around one airbrush; on the Hobby Heaven Zephyr they also keep the lid vent of the 7 ml cup (HHA-4101) open.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFive thicknesses: the finest for vents and cap holes, the heaviest for outlets\u003c\/li\u003e\n\u003cli\u003eSpiral wire profile that grips paint as it turns\u003c\/li\u003e\n\u003cli\u003eOne key ring holds all five\u003c\/li\u003e\n\u003cli\u003eDried plugs, lid vents, cap holes, fittings\u003c\/li\u003e\n\u003cli\u003eSold in a labelled Hobby Heaven bag, HHA-7202 and barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUsing them\u003c\/h3\u003e\n\u003cp\u003eSoften the paint before you probe: soak or flush with airbrush cleaner, as soft paint lifts far more easily. Withdraw the airbrush needle before working in the paint channel. Choose the thickest wire that slides in freely; a heavier one removes more each turn and bends less. Ease it in, roll it between finger and thumb, draw it out, wipe it and repeat until nothing comes back on it. Finish with another flush.\u003c\/p\u003e\n\u003cp\u003eA nozzle needs care. Remove it first (the wrench HHA-7101 does it on the Zephyr), probe only from the wide back end with a wire that enters easily, and never force one through or into the tip. Even the finest needle in the set should not be expected to pass a 0.2–0.3 mm nozzle; soak that tip instead.\u003c\/p\u003e\n\u003ch3\u003eBlockage, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSign\u003c\/th\u003e\n\u003cth\u003eLikely cause and remedy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOnly air comes out\u003c\/td\u003e\n\u003ctd\u003ePaint has set in the channel or nozzle: soak, then work a wire through the channel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint starts, then fades with the lid on\u003c\/td\u003e\n\u003ctd\u003eLid vent clogged, so no air replaces the paint: open it with the thinnest wire\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray split or off-centre\u003c\/td\u003e\n\u003ctd\u003eBent airbrush needle or damaged nozzle: replace the part, probing will not help\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCup fills with bubbles\u003c\/td\u003e\n\u003ctd\u003eNozzle or nozzle cap loose: seat them before anything else\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWire refuses to enter\u003c\/td\u003e\n\u003ctd\u003eHole smaller than that wire: pick a thinner one, as forcing bends it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCare and replacing\u003c\/h3\u003e\n\u003cp\u003eWipe each wire before paint dries on it. A slight bend can be eased straight with the fingers; a sharp kink means that one is finished. Never let them touch the polished outside of the airbrush, which they can scratch, and store the set on its ring in the bag, as fine wire is easy to lose.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eNeedles poke and brushes scrub: for the walls of passages and the inside of cups, use the brush set (HHA-7201). This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814987453,"sku":"HHA-7202","price":2.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-cleaning-needle-set-5-pcs-hha-7202-2.jpg?v=1795197625"},{"product_id":"hobby-heaven-airbrush-nozzle-cleaning-reamer-hha-7301","title":"Hobby Heaven Airbrush Nozzle Cleaning Reamer (HHA-7301) – with Screw-On Cap","description":"\u003cp\u003eHHA-7301 is a nozzle reamer: a slender taper with cutting edges along it, held in a grooved, gold-finish metal handle and closed by a screw-on cap. Paint that dries inside a nozzle tends to settle right at the tip, the narrowest opening in the whole airbrush, where a brush cannot reach. Eased into a removed nozzle and rotated, the edges shave that ring of dried paint away. It is a last resort rather than an everyday tool.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlender tapered tip with cutting edges\u003c\/li\u003e\n\u003cli\u003eGrooved handle for a light, controlled grip\u003c\/li\u003e\n\u003cli\u003eScrew-on cap that guards the point and your fingers\u003c\/li\u003e\n\u003cli\u003eFor dried paint inside a nozzle taken out of the airbrush\u003c\/li\u003e\n\u003cli\u003eHobby Heaven bag labelled HHA-7301, with barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBefore you reach for it\u003c\/h3\u003e\n\u003cp\u003eMost blocked nozzles clear without anything touching the inside. Remove the nozzle (HHA-7101 is the wrench for the Zephyr) and leave it in airbrush cleaner: minutes for fresh paint, longer for old. Look through it towards a lamp; a clean, round opening means it can go back in. Only if paint is still visible is the reamer needed.\u003c\/p\u003e\n\u003ch3\u003eUsing it\u003c\/h3\u003e\n\u003cp\u003eUnscrew the cap, hold the nozzle lightly, and slide the point into the opening until it just meets resistance. Then roll the handle slowly between finger and thumb a few times each way, with no pressure behind it, and let the edges remove the paint. Withdraw, wipe, hold it up to the lamp again and go back in only if needed. Rinse the nozzle before refitting it. Turn, never push: forcing the taper deeper stretches or splits the opening, and a damaged nozzle has to be replaced.\u003c\/p\u003e\n\u003ch3\u003eReaming, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat happens\u003c\/th\u003e\n\u003cth\u003eLook at this first\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir flows, paint does not\u003c\/td\u003e\n\u003ctd\u003eA blockage in the nozzle or channel: soak it, and ream only what the soak leaves\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpits at the start of every stroke\u003c\/td\u003e\n\u003ctd\u003eOften paint on the needle point or around the nozzle cap: clean those first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpray split or pulling sideways\u003c\/td\u003e\n\u003ctd\u003eBent needle point or split nozzle; reaming fixes neither\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBubbles appear in the cup\u003c\/td\u003e\n\u003ctd\u003eNozzle or its cap not tight: snug them gently\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOpening clear and round, yet the spray is poor\u003c\/td\u003e\n\u003ctd\u003eThen the nozzle is not the problem; check the needle, both caps and how thin the paint is\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eAfter each use, wipe the point and refit the cap straight away. Do not use it as a scribe or awl on other materials, and avoid dropping it tip first: a bent or dulled point is no good for a nozzle. Store it dry, with the cap fitted.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eThe finer the nozzle, the lighter the touch it needs. On the Zephyr a split nozzle is replaced by HHA-2101 (0.3 mm) or HHA-2102 (0.5 mm). This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436815020221,"sku":"HHA-7301","price":3.59,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-airbrush-nozzle-cleaning-reamer-hha-7301-2.jpg?v=1795197633"}],"url":"https:\/\/hobbyheaven.org\/en-ca\/collections\/hobby-heaven-zephyr-airbrush-system.oembed","provider":"Hobby Heaven","version":"1.0","type":"link"}