{"product_id":"hobby-heaven-zephyr-air-valve-hha-3401","title":"Hobby Heaven Zephyr Air Valve (HHA-3401) – Complete Assembled Replacement Valve","description":"\u003cp\u003eHHA-3401 is the air valve of the Hobby Heaven Zephyr, the unit beneath the trigger that your hose connects to. It is the airbrush's air switch: a spring holds a small piston shut until the trigger presses the valve pin down, air then rises through the airbrush towards the nozzle, and the moment you let go the spring shuts it off. It arrives as a single assembled unit with its O-ring, spring, piston and pin already in place, and one valve suits the Zephyr with either nozzle size, 0.3 mm or 0.5 mm.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eComplete and assembled, ready to screw in\u003c\/li\u003e\n\u003cli\u003eRubber O-ring fitted to seal the joint with the airbrush body\u003c\/li\u003e\n\u003cli\u003eKnurled collar for fitting and removing it by hand\u003c\/li\u003e\n\u003cli\u003eLower end is the Zephyr's air inlet, 1\/8\" BSP male, taking a hose directly or a quick-disconnect plug\u003c\/li\u003e\n\u003cli\u003eZephyr only; sold in a Hobby Heaven blister marked HHA-3401\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eValve, or something else?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSign\u003c\/th\u003e\n\u003cth\u003eProbable cause, then remedy\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir keeps coming after you release the trigger\u003c\/td\u003e\n\u003ctd\u003eValve not sealing, often paint or solvent inside: dry it, clean it and lubricate lightly before replacing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTrigger stays down or rises slowly\u003c\/td\u003e\n\u003ctd\u003eUsually the same sticky valve; clean first, replace if it persists\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss around the top of the valve\u003c\/td\u003e\n\u003ctd\u003eSnug it by hand and inspect its O-ring; replacements arrive with a fresh one\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHiss at the hose joint below\u003c\/td\u003e\n\u003ctd\u003eThe hose fitting or a quick-disconnect (HHA-5103) is leaking, not the valve; brush soapy water over the joint to find it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo air at all\u003c\/td\u003e\n\u003ctd\u003eFirst rule out the supply: compressor, regulator, hose; if air gets as far as the airbrush and stops, suspect the valve\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir arrives, paint does not\u003c\/td\u003e\n\u003ctd\u003eLook at the chucking nut (HHA-3202) or rear knob (HHA-3302)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eLeaking at rest or sticking after a proper clean and light lubrication, a bent pin, a damaged thread, or solvent damage that has not settled once the valve dried out.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eSwitch the compressor off and take the hose or coupler off the valve. Unscrew the old valve by its collar, confirm the O-ring is on the new one and run it in straight by hand until snug; no force or pliers are needed for it to seal. With no air connected, work the trigger several times to check it moves down freely and springs back, then reconnect: the air should stop the instant the trigger rises, with no hiss at the valve.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eKeep the valve out of solvent baths: thinner swells its rubber seals, the commonest reason a valve sticks. Take it out before you soak the body. A sticky valve needs only a drop of airbrush lubricant, never machine oil or penetrating spray. Its fit is confirmed on our Zephyr only. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436813512893,"sku":"HHA-3401","price":5.52,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-air-valve-hha-3401-2.jpg?v=1795192473","url":"https:\/\/hobbyheaven.org\/en-au\/products\/hobby-heaven-zephyr-air-valve-hha-3401","provider":"Hobby Heaven","version":"1.0","type":"link"}