{"product_id":"hobby-heaven-zephyr-0-3mm-nozzle-hha-2101","title":"Hobby Heaven Zephyr 0.3mm Nozzle (HHA-2101) – Replacement Airbrush Nozzle with O-Ring","description":"\u003cp\u003eHHA-2101 covers the 0.3 mm nozzle of the Hobby Heaven Zephyr, the size the airbrush ships with. It is the small threaded piece screwed into the nose of the body, and the needle tip sits in it. Draw the trigger back and the needle retracts from the opening, letting paint through to meet the air; release it and the needle closes the opening again. That thin tip is easy to split with over-enthusiastic wrench work or a needle rammed home. If your needle and caps are still sound, this one part is all the repair needs.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.3 mm: the Zephyr’s standard size, as supplied\u003c\/li\u003e\n\u003cli\u003eRubber O-ring already fitted on the thread\u003c\/li\u003e\n\u003cli\u003eScrews into the body; fitted and removed with the Zephyr nozzle wrench (HHA-7101)\u003c\/li\u003e\n\u003cli\u003ePacked in a transparent screw-cap pot lined with foam, sealed in a blister labelled HHA-2101\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIs it really the nozzle?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWhat you notice\u003c\/th\u003e\n\u003cth\u003eLikely cause\u003c\/th\u003e\n\u003cth\u003eWhat to get\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eUnder a magnifier the tip shows a crack, chip or flared edge\u003c\/td\u003e\n\u003ctd\u003eDamaged nozzle\u003c\/td\u003e\n\u003ctd\u003eThis nozzle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle point bent or hooked, nozzle opening clean and round\u003c\/td\u003e\n\u003ctd\u003eNeedle\u003c\/td\u003e\n\u003ctd\u003e0.3 mm needle HHA-2201\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBubbles appear in the cup as you spray\u003c\/td\u003e\n\u003ctd\u003eAir leaking round a loose nozzle or a tired O-ring\u003c\/td\u003e\n\u003ctd\u003eSnug it up; replace if bubbles persist\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePaint stops or comes in bursts after the airbrush stood unused\u003c\/td\u003e\n\u003ctd\u003ePaint dried inside the tip\u003c\/td\u003e\n\u003ctd\u003eSoak and clean before buying anything\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeedle and nozzle both worn out, or a cap gone missing\u003c\/td\u003e\n\u003ctd\u003eMore than one part\u003c\/td\u003e\n\u003ctd\u003eWhole 0.3 mm set HHA-2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSigns it needs replacing\u003c\/h3\u003e\n\u003cp\u003eA healthy nozzle has a clean, round opening when viewed through a loupe or zoomed phone camera. A split or splayed edge cannot be cleaned away, and nor can a spray line that drifts sideways once the airbrush is stripped and clean.\u003c\/p\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eShut off and unplug the air supply, then flush the airbrush clean.\u003c\/li\u003e\n\u003cli\u003eTake off both caps, loosen the needle chucking nut and ease the needle back clear of the nozzle.\u003c\/li\u003e\n\u003cli\u003eUndo the worn nozzle using the wrench and check its O-ring has come out too.\u003c\/li\u003e\n\u003cli\u003eTurn the new one in by hand, then give the wrench only a slight nudge. Over-tightening is how nozzles split.\u003c\/li\u003e\n\u003cli\u003eRefit the caps, slide the needle forward until it stops in its seat, tighten the chucking nut and check on clean water before paint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eSoak a blocked nozzle, out of the airbrush, in cleaner; never push a pin through it. The reamer HHA-7301 is the last resort, turned gently.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAlone, it will not move a Zephyr to 0.5 mm. The needle, the nozzle and the two caps change together: that is the HHA-2002 set.\u003c\/li\u003e\n\u003cli\u003eBuilt for the Zephyr alone: we make no claim that it fits any other airbrush.\u003c\/li\u003e\n\u003cli\u003eOne of the numbered parts of our Zephyr system, which keeps growing; reorder by the HHA code on the pack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436811579581,"sku":"HHA-2101","price":7.72,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-zephyr-0-3mm-nozzle-hha-2101-2.jpg?v=1795190834","url":"https:\/\/hobbyheaven.org\/en-au\/products\/hobby-heaven-zephyr-0-3mm-nozzle-hha-2101","provider":"Hobby Heaven","version":"1.0","type":"link"}