{"product_id":"hobby-heaven-braided-airbrush-hose-3m-hha-5202","title":"Hobby Heaven Braided Airbrush Hose 3m (HHA-5202) – 1\/8\" BSP Both Ends","description":"\u003cp\u003eHHA-5202 is a 3 m braided air hose, long enough for the compressor to live on the floor, beneath the bench or next to a spray booth rather than at your elbow, which also takes its noise further from your ear and leaves room to turn a model or stand up. The two ends carry matching knurled nuts threaded 1\/8\" BSP female, so direction does not matter and both tighten by hand. It suits the Hobby Heaven Zephyr, as our photo shows, and any other airbrush or compressor with 1\/8\" BSP male connections. If the compressor sits right beside you, the shorter HHA-5201 (1.8 m) leaves less hose lying on the desk.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e3 m long, roughly 10 ft\u003c\/li\u003e\n\u003cli\u003eMatching 1\/8\" BSP female nuts, knurled for grip\u003c\/li\u003e\n\u003cli\u003eBlack braid over its whole length\u003c\/li\u003e\n\u003cli\u003ePictured on the Zephyr with our valved quick disconnect, HHA-5104, sold separately\u003c\/li\u003e\n\u003cli\u003eComes in a Hobby Heaven bag marked HHA-5202 with its barcode\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhich hose for your setup?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYour setup\u003c\/th\u003e\n\u003cth\u003eWhat to use\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor on the desk or a shelf just behind\u003c\/td\u003e\n\u003ctd\u003e1.8 m (HHA-5201) is enough\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor on the floor, beneath the bench or by a booth\u003c\/td\u003e\n\u003ctd\u003eThis 3 m hose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eZephyr, Iwata, Harder \u0026amp; Steenbeck, Sparmax, Grex or Master airbrush\u003c\/td\u003e\n\u003ctd\u003e1\/8\" BSP inlet: connects directly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBadger, Paasche or Aztek airbrush\u003c\/td\u003e\n\u003ctd\u003eFit that brand's inlet adapter first\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor outlet 1\/8\" BSP male\u003c\/td\u003e\n\u003ctd\u003eConnects directly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompressor outlet 1\/4\" BSP male\u003c\/td\u003e\n\u003ctd\u003eAdd a 1\/4\" female to 1\/8\" male reducer (in HHA-5401)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUS compressor with 1\/4\" NPT\u003c\/td\u003e\n\u003ctd\u003eAn NPT-to-BSP adapter: the two threads do not seal together\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhen the air misbehaves\u003c\/h3\u003e\n\u003cp\u003eHoses seldom fail. A hiss at an end is nearly always the joint: refit the nut squarely and, if it persists, tape the male thread. A nut that stops after one turn has met a different thread, so reach for an adapter rather than force. Water spitting from the nozzle is condensation from the compressor; an inline trap such as HHA-5301 catches it at the airbrush. Air leaking through the braid means a split, usually from crushing or kinking, and then the hose should go, as it should when a nut cracks or its thread strips.\u003c\/p\u003e\n\u003ch3\u003eFitting and care\u003c\/h3\u003e\n\u003cp\u003eSwitch off at the compressor and bleed the line. Tighten one end on the outlet and the far end on the airbrush or a quick-disconnect coupler, by hand. Restore the air and dab soapy water on each connection to spot bubbles. Set your pressure while spraying, because any hose reads a touch lower with air flowing. Coil it loosely and keep solvents, soldering irons and knives clear of it.\u003c\/p\u003e\n\u003ch3\u003eWorth knowing\u003c\/h3\u003e\n\u003cp\u003eOne long hose avoids joining two short ones, and so removes a joint that could leak. This is one of the numbered parts of the Hobby Heaven Zephyr range, which keeps growing; once a number is given, it always means the same part.\u003c\/p\u003e","brand":"Hobby Heaven","offers":[{"title":"Default Title","offer_id":68436814463165,"sku":"HHA-5202","price":9.23,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0271\/9583\/4503\/files\/hobby-heaven-braided-airbrush-hose-3m-hha-5202-2.jpg?v=1795199865","url":"https:\/\/hobbyheaven.org\/en-au\/products\/hobby-heaven-braided-airbrush-hose-3m-hha-5202","provider":"Hobby Heaven","version":"1.0","type":"link"}